2005-2008 Yaris · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Aug 2005


CHECK IGNITION SWITCH
B122831E01
  1. Disconnect the D55 switch connector.

  2. Measure the resistance of the wire harness side connector.

    Standard resistance: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (D55-5) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D55 switch connector.

  4. Measure the resistance and voltage of the connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (D55-8) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    VC5 (D55-14) - AGND (D55-8)
    P - BR
    Power supply
    Engine immobiliser system is set
    (key is not in cabin)
    Below 1 V
    VC5 (D55-14) - AGND (D55-8)
    P - BR
    Power supply
    Press ignition switch*
    4.6 to 5.4 V
    CODE (D55-10) - AGND (D55-8)
    O - BR
    Demodulated signal of key code data
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    CODE (D55-10) - AGND (D55-8)
    O - BR
    Demodulated signal of key code data
    Ignition switch pushed and key held close to ignition switch*
    Pulse generation
    (see waveform 1)
    TXCT (D55-9) - AGND (D55-8)
    V - BR
    Key code output signal
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    TXCT (D55-9) - AGND (D55-8)
    V - BR
    Key code output signal
    Ignition switch pushed and key held close to ignition switch*
    Pulse generation
    (see waveform 2)

    HINT:
    *: Remove the key's battery before performing this inspection.

    1. If the result is not as specified, the switch may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B051053E01
      Waveform 1
      Item
      Content
      Symbols (Terminal No.)
      CODE (D55-10) - AGND (D55-8)
      Tool Setting
      2 V/DIV., 20 msec./DIV.
      Condition
      Ignition switch pushed and key held close to ignition switch*

      HINT:
      *: Remove the key's battery before performing this inspection.

    2. B051052E01
      Waveform 2
      Item
      Content
      Symbols (Terminal No.)
      TXCT (D55-9) - AGND (D55-8)
      Tool Setting
      2 V/DIV., 20 msec./DIV.
      Condition
      Ignition switch pushed and key held close to ignition switch*

      HINT:
      *: Remove the key's battery before performing this inspection.


CHECK CERTIFICATION ECU
B108931E01
  1. Disconnect the D60 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (D60-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B1 (D60-1) - E (D60-17)
    B - W-B
    +B power supply
    Always
    11 to 14 V
    IG (D60-18) - E (D60-17)
    BR - W-B
    Ignition power supply
    ignition switch off
    Below 1 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D60 connector.

  4. Measure the resistance and voltage of the connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (D60-40) - Body ground
    BR - Body ground
    Ignition switch ground
    Always
    Below 1 Ω
    VC5 (D60-30) - AGND (D60-40)
    P - BR
    Ignition switch power supply
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    VC5 (D60-30) - AGND (D60-40)
    P - BR
    Ignition switch power supply
    Ignition switch pushed*
    4.6 to 5.4 V
    CODE (D60-9) - AGND (D60-40)
    O - BR
    Ignition switch CODE input
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    CODE (D60-9) - AGND (D60-40)
    O - BR
    Ignition switch CODE input
    Ignition switch pushed and key held close to ignition switch*
    Pulse generation
    (see waveform 1)
    TXCT (D60-8) - AGND (D60-40)
    V - BR
    Ignition switch TX output
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    TXCT (D60-8) - AGND (D60-40)
    V - BR
    Ignition switch TX output
    Ignition switch pushed and key held close to ignition switch*
    Pulse generation
    (see waveform 2)

    HINT:
    *: Remove the key's battery before performing this inspection.

    1. If the result is not as specified, the ECU may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B051053E01
      Waveform
      Item
      Content
      Symbols (Terminal No.)
      CODE (D60-9) - AGND (D60-40)
      Tool Setting
      2 V/DIV., 20 msec./DIV.
      Condition
      Ignition switch pushed and key held close to ignition switch*

      HINT:
      *: Remove the key's battery before performing this inspection.

    2. B051052E01
      Waveform 2
      Item
      Content
      Symbols (Terminal No.)
      TXCT (D60-8) - AGND (D60-40)
      Tool Setting
      2 V/DIV., 20 msec./DIV.
      Condition
      Ignition switch pushed and key held close to ignition switch*

      HINT:
      *: Remove the key's battery before performing this inspection.


CHECK ID CODE BOX
B108932E01
  1. Disconnect the D58 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (D58-8) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    EGND (D58-7)* - Body ground
    BR* - Body ground
    Ground for ECM
    Always
    Below 1 Ω
    +B (D58-1) - GND (D58-8)
    L - W-B
    +B power supply
    Always
    11 to 14 V
    *: For 2SZ-FE and 2ZR-FE.
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D58 ECU connector.

  4. Measure the voltage of the connector.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    EFII (D58-5) - GND (D58-8)
    O - W-B
    ECM input signal
    Ignition switch off
    Below 1 V
    EFII (D58-5) - GND (D58-8)
    O - W-B
    ECM input signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 1)
    EFIO(D58-6) - GND (D58-8)
    W - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    EFIO (D58-6) - GND (D58-8)
    W - W-B
    ECM output signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    1. If the result is not as specified, the ECU may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B051051E01
      Waveform 1
      Item
      Content
      Symbols (Terminal No.)
      EFII (D58-5) - GND (D58-8)
      Tool Setting
      10 V/DIV., 100 msec./DIV.
      Condition
      Ignition switch on (IG)

    2. B051050E01
      Waveform 2
      Item
      Content
      Symbols (Terminal No.)
      EFIO (D58-6) - GND (D58-8)
      Tool Setting
      10 V/DIV., 100 msec./DIV.
      Condition
      Ignition switch on (IG)


CHECK STEERING LOCK ECU
B106649E06
  1. Disconnect the D56 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Standard 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    SGND (D56-2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND (D56-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B (D56-7) - Body ground
    R - Body ground
    +B power supply
    Always
    11 to 14 V
    IG2 (D56-6) - Body ground
    R - Body ground
    Ignition power supply
    Ignition switch off
    0 V
    IG2 (D56-6) - Body ground
    R - Body ground
    Ignition power supply
    Ignition switch on (IG)
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK ECM (1KR-FE)
A116116E02

HINT:
The standard normal value between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal value for that pair of terminals, displayed in the specified condition column. The illustration above can be used as a reference to identify the ECM terminal locations.

  1. Measure the resistance and voltage of the connector.

    Standard 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (A32-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E2 (C33-36) - Body ground
    P - Body ground
    Ground
    Always
    Below 1 Ω
    E21 (C33-35) - Body ground
    G - Body ground
    Ground
    Always
    Below 1 Ω
    E01 (A32-20) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    BATT (A32-22) - E1 (A32-1)
    V - W-B
    Battery (for measuring battery voltage and for ECM memory)
    Always
    11 to 14 V
    IGSW (A32-4) - E1 (A32-1)
    R - W-B
    Ignition switch
    Ignition switch on (IG)
    11 to 14 V
    +B (A32-24) - E1 (A32-1)
    B - W-B
    Power source of ECM
    Ignition switch on (IG)
    11 to 14 V
    +B1 (A32-23) - E1 (A32-1)
    B - W-B
    Power source of ECM
    Ignition switch on (IG)
    11 to 14 V
    IMI (A32-31) - E1 (A32-1)
    W - W-B
    ID code box input signal
    Ignition switch off
    Below 1 V
    IMI (A32-31) - E1 (A32-1)
    W - W-B
    ID code box input signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 1)
    IMO (A32-40) - E1 (A32-1)
    O - W-B
    ID code box output signal
    Ignition switch off
    Below 1 V
    IMO (A32-40) - E1 (A32-1)
    O - W-B
    ID code box output signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    1. If the result is not as specified, the ECM may have a malfunction.

  2. Inspect using an oscilloscope.

    1. B051050E01
      Waveform 1
      Item
      Content
      Symbols (Terminal No.)
      IMI (A32-31) - E1 (A32-1)
      Tool Setting
      10 V/DIV., 100 msec./DIV.
      Condition
      Ignition switch on (IG)

    2. B051051E01
      Waveform 2
      Item
      Content
      Symbols (Terminal No.)
      IMO (A32-40) - E1 (A32-1)
      Tool Setting
      10 V/DIV., 100 msec./DIV.
      Condition
      Ignition switch on (IG)


CHECK ECM (2SZ-FE, 2ZR-FE)
A107881E08

HINT:
The standard normal value between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal value for that pair of terminals, displayed in the specified condition column. The illustration above can be used as a reference to identify the ECM terminal locations.

  1. Measure the resistance and voltage of the connector.

    Standard 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (C20-104) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    EOM (A21-9) - Body ground
    BR - Body ground
    Ground for ID code box
    Always
    Below 1 Ω
    ME01 (C20-43) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    E01 (C20-45) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    E03 (C20-86) - Body ground
    BR*1 - Body ground
    W-B*2 - Body ground
    Ground
    Always
    Below 1 Ω
    BATT (A21-20) - E1 (C20-104)
    Y - W
    Battery (for measuring battery voltage and for ECM memory)
    Always
    11 to 14 V
    IGSW (A21-28) - E1 (C20-104)
    R - W
    Ignition switch
    Ignition switch on (IG)
    11 to 14 V
    +B (A21-2) - E1 (C20-104)
    B - W
    Power source of ECM
    Ignition switch on (IG)
    11 to 14 V
    +BM (A21-3) - E1 (C20-104)
    GR - W
    Power source of ECM
    Ignition switch on (IG)
    11 to 14 V
    IMI (A21-11) - EOM (A21-9)
    W - BR
    ID code box input signal
    Ignition switch off
    Below 1 V
    IMI (A21-11) - EOM (A21-9)
    W - BR
    ID code box input signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 1)
    IMO (A21-10) - EOM (A21-9)
    O - BR
    ID code box output signal
    Ignition switch off
    Below 1 V
    IMO (A21-10) - EOM (A21-9)
    O - BR
    ID code box output signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    *1: 2SZ-FE
    *2: 2ZR-FE
    1. If the result is not as specified, the ECM may have a malfunction.

  2. Inspect using an oscilloscope.

    1. B051050E01
      Waveform 1
      Item
      Content
      Symbols (Terminal No.)
      IMI (A21-11) - EOM (A21-9)
      Tool Setting
      10 V/DIV., 100 msec./DIV.
      Condition
      Ignition switch on (IG)

    2. B051051E01
      Waveform 2
      Item
      Content
      Symbols (Terminal No.)
      IMO (A21-10) - EOM (A21-9)
      Tool Setting
      10 V/DIV., 100 msec./DIV.
      Condition
      Ignition switch on (IG)


CHECK ECM (1ND-TV)
A115971E01
  1. Measure the resistance and voltage of the connector.

    Standard 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (A49-2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E2 (A49-43) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E11 (A49-41) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    IGSW (A49-70) - E1 (A49-2)
    R - W-B
    Ignition switch
    Ignition switch on (IG)
    11 to 14 V
    +B (A49-42) - E1 (A49-2)
    B - W-B
    Power source of ECM
    Ignition switch on (IG)
    11 to 14 V
    +B1 (A49-1) - E1 (A49-2)
    B - W-B
    Power source of ECM
    Ignition switch on (IG)
    11 to 14 V
    IMI (A49-6) - E1 (A49-2)
    W - W-B
    ID code box input signal
    Ignition switch off
    Below 1 V
    IMI (A49-6) - E1 (A49-2)
    W - W-B
    ID code box input signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 1)
    IMO (A49-4) - E1 (A49-2)
    O - W-B
    ID code box output signal
    Ignition switch off
    Below 1 V
    IMO (A49-4) - E1 (A49-2)
    O - W-B
    ID code box output signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    1. If the result is not as specified, the ECM may have a malfunction.

  2. Inspect using an oscilloscope.

    1. B051050E01
      Waveform 1
      Item
      Content
      Symbols (Terminal No.)
      IMI (A49-6) - E1 (A49-2)
      Tool Setting
      10 V/DIV., 100 msec./DIV.
      Condition
      Ignition switch on (IG)

    2. B051051E01
      Waveform 2
      Item
      Content
      Symbols (Terminal No.)
      IMO (A49-4) - E1 (A49-2)
      Tool Setting
      10 V/DIV., 100 msec./DIV.
      Condition
      Ignition switch on (IG)


CHECK MAIN BODY ECU
E114510E04
B108612E02
  1. Disconnect the 4B, 4D, 4E and D65 ECU connectors.

  2. Measure the resistance and voltage of the wire harness side connectors.

    Standard 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND1 (4E-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND2 (D65-4) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    AM1 (D65-1) - Body ground
    O -Body ground
    +B power supply
    Always
    11 to 14 V
    AM2 (D64-6) - Body ground
    SB -Body ground
    +B power supply
    Always
    11 to 14 V
    SSW1 (D65-10) - Body ground
    R -Body ground
    Ignition switch
    Ignition switch off
    10 kΩ or higher
    SSW1 (D65-10) - Body ground
    R -Body ground
    Ignition switch
    Ignition switch on (IG)
    Below 1 Ω
    SSW2 (D65-9) - Body ground
    L -Body ground
    Ignition switch
    Ignition switch off
    10 kΩ or higher
    SSW2 (D65-9) - Body ground
    L -Body ground
    Ignition switch
    Ignition switch on (IG)
    Below 1 Ω
    BECU (4B-30) - Body ground
    L - Body ground
    +B power supply
    Always
    11 to 14 V
    LIN1 (4D-9) - Body ground
    P - Body ground
    LIN communication line
    Always
    10 kΩ or higher
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

← PROBLEM SYMPTOMS TABLE (from Nov 2006)DIAGNOSIS SYSTEM (from Aug 2005) →