Home › ENGINE › 1KR-FE FUEL › FUEL PUMP
INSTALLATION
Removal / installation · Vehicles built Aug 2005 – Oct 2005
Versions by build date: Aug 2005 – Oct 2005 from Nov 2005
NOTICE:
Always use "Torx" socket wrench E10 when installing the rear seat.
1.
INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Install a new fuel suction tube gasket onto the fuel tank.
Align the protrusion of the fuel pump with the cutout of the fuel tank and install the fuel suction with pump and gauge tube assembly.
NOTICE:
The arm of the sender gauge should not be bent.
2.
INSTALL FUEL PUMP GAUGE RETAINER
Using SST, turn the retainer 540° clockwise from the screw starting point and align the claw of the retainer with the matchmark on the fuel tank.
SST
09808-14020
(09808-01410, 09808-01420, 09808-01430)
NOTICE:
Replace the fuel pump gauge retainer with a new one if not installed properly.
Part No. 77144-52040
HINT:
Align the claws of the fuel pump gauge retainer and the tips of SST.
At the point where the retainer is turned 90° from the start of the thread, push the retainer in from the opposite side to the start of the thread. Check that the thread of the retainer is properly engaged with that on the fuel tank.
3.
CONNECT CANISTER OUTLET HOSE SUB-ASSEMBLY NO. 1
Connect the canister outlet hose.
4.
CONNECT FUEL EMISSION TUBE NO. 2
Connect fuel emission tube No. 2.
5.
CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Insert the fuel tank main tube.
Install the tube joint clip.
NOTICE:
Check that there are no scratches or foreign objects on the connecting parts.
Check that the fuel tube joint is inserted securely.
Check that the fuel tube joint clip is on the collar of the fuel tube joint.
After installing the tube joint clip, check that the fuel tube joint have not been pulled off.
Do not damage any clip. If a clip is damaged, replace it.
6.
INSTALL REAR FLOOR SERVICE HOLE COVER
Connect the fuel pump connector.
Install the rear floor service hole cover with new butyl tape.
7.
INSTALL REAR SEAT ASSEMBLY
Insert the 2 location pins through the 2 body holes and install the rear seat.
Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
Torque:
37 N*m{
375 kgf*cm
, 27 ft.*lbf
}
Install the rear seat cushion.
Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.
Torque:
37 N*m{
375 kgf*cm
, 27 ft.*lbf
}
8.
INSTALL REAR SEAT LEG COVER NO. 2
Engage the 3 claws and install the No. 2 rear seat leg cover.
9.
INSTALL REAR SEAT LEG COVER NO. 1
Engage the 4 claws and install the No. 1 rear seat leg cover.
10.
INSTALL DECK FLOOR BOX (w/ Deck Board)
Install the deck floor box and lock the 2 knobs.
11.
INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)
Install the spare wheel cover.
12.
INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)
Set the deck board and lock the 2 knobs.
13.
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
Engage the 2 claws and install the package tray trim panel.
Install the 5 pieces of hook tape.
Install the 2 package tray trim suspenders.
14.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque:
5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}
15.
CHECK FOR FUEL LEAKAGE