INSTALLATION
Removal / installation · Vehicles built from Aug 2005
- NOTICE:
- Always use "Torx" socket wrench E10 when installing the rear seat.
| 1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
![]() ![]() |
Install a new fuel suction tube gasket onto the fuel tank.
Align the protrusion of the fuel pump with the cutout of the fuel tank and install the fuel suction with pump and gauge tube assembly.

- NOTICE:
- The arm of the sender gauge should not be bent.
| 2. INSTALL FUEL PUMP GAUGE RETAINER |
![]() ![]() |
Using SST, turn the retainer 540° clockwise from the screw starting point and align the claw of the retainer with the matchmark on the fuel tank.
- SST
- 09808-14020
(09808-01410, 09808-01420, 09808-01430)
- NOTICE:
- Replace the fuel pump gauge retainer with a new one if not installed properly.
- Part No. 77144-52040
- HINT:
- Align the claws of the fuel pump gauge retainer and the tips of SST.
- At the point where the retainer is turned 90° from the start of the thread, push the retainer in from the opposite side to the start of the thread. Check that the thread of the retainer is properly engaged with that on the fuel tank.
- Align the claws of the fuel pump gauge retainer and the tips of SST.
| 3. CONNECT CANISTER OUTLET HOSE SUB-ASSEMBLY NO. 1 |
![]() ![]() |
Connect the canister outlet hose.
| 4. CONNECT FUEL EMISSION TUBE NO. 2 |
![]() ![]() |
Connect the fuel emission tube.
| 5. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
![]() ![]() |
Insert the fuel tank main tube.
Install the tube joint clip.
- NOTICE:
- Check that there are no scratches or foreign objects on the connecting parts.
- Check that the fuel tube joint is inserted securely.
- Check that the fuel tube joint clip is on the collar of the fuel tube joint.
- After installing the tube joint clip, check that the fuel tube joint have not been pulled off.
- Do not damage any clip. If a clip is damaged, replace it.
- Check that there are no scratches or foreign objects on the connecting parts.
| 6. INSTALL REAR FLOOR SERVICE HOLE COVER |
![]() ![]() |
Connect the fuel pump connector.
Install the rear floor service hole cover with new butyl tape.

| 7. INSTALL REAR SEAT ASSEMBLY |
Insert the 2 location pins through the 2 body holes and install the rear seat.

Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
Install the rear seat cushion.

Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
| 8. INSTALL REAR SEAT LEG COVER NO. 2 |
Engage the 3 claws and install the No. 2 rear seat leg cover.

| 9. INSTALL REAR SEAT LEG COVER NO. 1 |
Engage the 4 claws and install the No. 1 rear seat leg cover.

| 10. INSTALL DECK FLOOR BOX (w/ Deck Board) |
Install the deck floor box and lock the 2 knobs.

| 11. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
Install the spare wheel cover.

| 12. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
Set the deck board and lock the 2 knobs.

| 13. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY |
Engage the 2 claws and install the package tray trim panel.

Install the 5 pieces of hook tape.
Install the 2 package tray trim suspenders.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 15. CHECK FOR FUEL LEAKAGE |
When using the intelligent tester.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and intelligent tester main switch on.
- NOTICE:
- Do not start the engine.
Select the Active Test mode on the intelligent tester.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Check that there is no fuel leakage anywhere on the fuel system after doing maintenance.






