INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL FUEL SENDER GAUGE ASSEMBLY |
![]() ![]() |
Install the fuel sender gauge onto the fuel suction with pump and gauge tube.
Connect the fuel sender gauge connector.

| 2. INSTALL FUEL TANK SUCTION TUBE GASKET |
![]() ![]() |
Install a new fuel tank suction tube gasket onto the fuel tank.
| 3. INSTALL FUEL TANK VENT TUBE WITH SENDER GAUGE ASSEMBLY |
![]() ![]() |
Align the protrusion of the fuel tank vent tube with sender gauge with the cutout of the fuel tank and install the fuel tank vent tube with sender gauge assembly.
- NOTICE:
- The arm of the sender gauge should not be bent.
| 4. INSTALL FUEL PUMP GAUGE RETAINER |
Align the end of the threads of a new fuel pump gauge retainer with that of the fuel tank.
Set SST to the fuel pump gauge retainer.

- SST
- 09808-14020
(09808-01410, 09808-01420, 09808-01430)
- NOTICE:
- Use SST. Do not use any other tools such as a screwdriver.
- As the fuel pipes are located on the track of SST, SST should be reset a few times to prevent it from coming into contact with the pipes when installing the fuel pump gauge retainer.
- Use SST. Do not use any other tools such as a screwdriver.
- HINT:
- Fit the rib on the fuel pump gauge retainer into the cutout of SST.
While holding the fuel pump assembly by hand, use SST to tighten the fuel pump gauge retainer one and half turns so that the mark on the retainer is within the range indicated in the illustration.

| 5. CONNECT FUEL RETURN TUBE SUB-ASSEMBLY |
Insert the fuel tank return tube.
Install the tube joint clip.


- NOTICE:
- Check that there are no scratches or foreign matter on the joint.
- Make sure that the fuel tank main tube is inserted all the way to the end.
- Check that the tube joint clip is installed onto the rim of the fuel tank main tube.
- After connecting the fuel tube connector and the fuel pipe, check that they are securely connected by pulling on them.
- Do not damage any clips. If a clip is damaged, replace it.
- Check that there are no scratches or foreign matter on the joint.
| 6. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
Insert the fuel tank main tube.
Install the tube joint clip.


- NOTICE:
- Check that there are no scratches or foreign matter on the joint.
- Make sure that the fuel tank main tube is inserted all the way to the end.
- Check that the tube joint clip is installed onto the rim of the fuel tank main tube.
- After connecting the fuel tube connector and the fuel pipe, check that they are securely connected by pulling on them.
- Do not damage any clips. If a clip is damaged, replace it.
- Check that there are no scratches or foreign matter on the joint.
| 7. INSTALL REAR FLOOR SERVICE HOLE COVER |
![]() ![]() |
Connect the fuel sender gauge connector.
Install the rear floor service hole cover with new butyl tape.

Install the floor carpet with the clip.

| 8. INSTALL REAR SEAT ASSEMBLY |
Insert the 2 location pins through the 2 body holes and install the rear seat.

Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
Install the rear seat cushion.

Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
| 9. INSTALL NO. 2 REAR SEAT LEG COVER |
Engage the 6 claws and install the No. 2 rear seat leg cover.

| 10. INSTALL DECK FLOOR BOX LH (w/ Deck Board) |
- HINT:
- Use the same procedure as for the RH side.
| 11. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
Install the spare wheel cover.

| 12. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
Set the deck board and lock the 2 knobs.

| 13. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
Install the rear floor carpet.

| 14. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Deck Board) |
Engage the 2 claws and install the package tray trim panel.

Install the 5 pieces of hook tape.
Install the 2 package tray trim suspenders.
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 16. CHECK FOR FUEL LEAK |




