2005-2008 Yaris · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. CLEAN WINDSHIELD GLASS

B073128E01
  1. Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.

  1. Clean the outer circumference of the windshield glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.


2. CLEAN VEHICLE BODY

B073084E02
  1. Clean and shape the contact surface of the vehicle body.

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.


3. INSTALL WINDSHIELD GLASS STOPPER NO. 1

B107866
  1. Install 2 new stoppers onto the vehicle body, as shown in the illustration.


4. INSTALL WINDSHIELD GLASS STOPPER NO. 2

B107883E01
  1. Apply Primer G to the installation parts of the stoppers.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new stoppers onto the windshield glass, as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    40 mm (1.57 in.)
    b
    14.5 mm (0.571 in.)


5. INSTALL WINDSHIELD OUTSIDE MOULDING

B127221E01
  1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Do not coat the adhesive with Primer G.
    3. Throw away any leftover Primer G.

  1. Install the moulding onto the windshield glass, as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    0.1mm (0.004 in.)


6. INSTALL WINDOW GLASS ADHESIVE DAM
  1. Apply Primer G to the installation part of a new dam, as shown in the illustration.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. B107885E01
    Install the new dam with double-sided tape as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    32 mm (1.26 in.)


7. INSTALL WINDSHIELD GLASS

  1. B116960E01
    Position the windshield glass.

    1. Using suction cups, place the windshield glass in the correct position.

    2. Check that the entire contact surface of the windshield glass rim is perfectly even.

    3. Place matchmarks on the windshield glass and vehicle body.

      NOTICE:
      Check that the stoppers are correctly attached to the vehicle body.

      HINT:
      When reusing a windshield glass, check and correct the matchmark positions.

    4. Using suction cups, remove the windshield glass.

  1. B106027E01
    Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.

  1. Using a brush or sponge, apply Primer G to the edge of the windshield glass and the contact surface.

    B107886E01

    Specification:
    Area
    Measurement
    a
    8.0 mm (0.315 in.)
    b
    19 mm (0.748 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

  1. Apply adhesive.

    Adhesive:
    Part No. 08850-00801 or the equivalent


    1. B106205E01
      Cut the tip off the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the times indicated in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the windshield glass, as shown in the illustration.

      B107887E01

      Specification:
      Area
      Measurement
      a
      8 mm (0.315 in.)
      b
      12 mm (0.472 in.)
      c
      10 mm (0.394 in.)
      d
      17.5 mm (0.689 in.)

  1. B116960E02
    Install the windshield glass onto the vehicle body.

    1. Using suction cups, position the windshield glass so that the matchmarks are aligned. Gently press it in along the rim.

      NOTICE:
      1. Allow the primer to dry for 3 minutes or more.
      2. Check that the stoppers are attached to the vehicle body correctly.
      3. Check that there is a small gap between the vehicle body and the windshield glass.

    2. Gently press the front surface of the windshield glass to ensure that the windshield glass is securely fitted to the vehicle body.

    3. B073131E01
      Using a scraper, remove any excessive or protruding adhesive.

      HINT:
      Apply adhesive to the windshield glass rim.

      NOTICE:
      Do not to drive the vehicle within the time indicated in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours


8. CHECK FOR LEAKAGE AND REPAIR
  1. Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.


9. INSTALL INNER REAR VIEW MIRROR ASSEMBLY

B087505
  1. Slide the inner rear view mirror to install it.

  1. B118044
    Engage the 2 claws and install the cover.


10. INSTALL ROOF HEADLINING

11. INSTALL FRONT PILLAR GARNISH RH

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127674
      Connect the speaker connector.

  1. B114312
    Install the 3 antenna cord clamps.

  1. Connect the connector.

  1. w/ Curtain Shield Airbag:

    1. B117697E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B117694
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


12. INSTALL FRONT PILLAR GARNISH LH

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127673
      Connect the speaker connector.

  1. B114316
    Install the 4 wire harness clamps.

  1. w/ Curtain Shield Airbag:

    1. B117698E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B114318
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


13. INSTALL MAP LIGHT ASSEMBLY

E114447
  1. Connect the connector.

  1. Engage the 4 claws and install the map light.


14. INSTALL VISOR HOLDER RH

  1. B114350E01
    Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.


15. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.


16. INSTALL VISOR ASSEMBLY RH

  1. B114304
    Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.

  1. B114351
    Engage the 4 claws and install the visor bracket cover.


17. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


18. INSTALL ASSIST GRIP SUB-ASSEMBLY

B114302

HINT:
The number of the assist grips varies with the specifications.

  1. Engage the 2 springs and install the assist grip.


19. INSTALL ASSIST GRIP COVER

B114352

HINT:
The number of the assist grip covers varies with the specifications.

  1. Engage the 2 claws and install the assist grip cover.


20. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)

B114353

HINT:
The number of the roof headlining service hole covers varies with the specifications.

  1. Install the roof headlining service hole cover.


21. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B130371E01
    Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Gold
    LH side
    Silver


22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


23. INSTALL COWL SIDE TRIM BOARD RH

  1. B114285
    Engage the claw and stud bolt and install the cowl side trim board.


24. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


25. INSTALL FRONT DOOR SCUFF PLATE RH

  1. B114284
    Engage the 8 claws and install the front door scuff plate.


26. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


27. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


28. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


29. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


30. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


31. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


32. INSTALL FRONT WIPER ARM BLADE ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


33. INSTALL FRONT WIPER ARM BLADE ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


34. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


36. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Aug 2005)COMPONENTS (from Jan 2006) →