2005-2008 Yaris · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Nov 2005


DATA LIST

HINT:
By reading the Data List displayed on an intelligent tester, values can be checked, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.

NOTICE:
In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect an intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn the tester on.

  6. Select the following menu items: Powertrain / Engine and ECT / Data List.

  7. Check the values by referring to the table below.

    intelligent tester Display
    Measurement: Range
    (Display)
    Normal Conditions *
    Diagnostic Notes
    Injection Volume
    (INJ VOLUME)
    Injection volume:
    Min.: 0 mm3, Max.: 1,279.98 mm3
    3 to 8 mm3: Idling
    -
    Engine SPD
    (ENGINE SPD)
    Engine speed:
    Min.: 0 rpm, Max.: 16,383.75 rpm
    720 to 820 rpm: Idling
    -
    MAF
    (MAF)
    Air flow rate from Mass Air Flow (MAF) meter status:
    Min.: 0 g/sec, Max.: 655.35 g/sec
    1. 5.0 to 6.0 g/sec: Idling
    2. 13.1 to 18.9 g/sec:
      Running without load (2,500 rpm)
    If value approximately 0.0 g/sec:
    1. MAF meter power source circuit open
    2. VG circuit open or shorted
    If value 135 g/sec or more:
    1. E2G circuit open
    PIM
    (PIM)
    Absolute pressure inside intake manifold:
    Min.: 0 kPa, Max.: 255 kPa
    1. 85 to 110 kPa: Idling
    2. 90 to 115 kPa:
      Engine running at 2,000 rpm
    -
    Coolant Temp
    (COOLANT TEMP)
    Engine coolant temperature:
    Min.: -40°C, Max.: 215°C
    80° to 95°C (176° to 203°F):
    After warming up engine
    If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
    Intake Air
    (INTAKE AIR)
    Intake air temperature:
    Min.: -40°C, Max.: 215°C
    Equivalent to temperature at intake manifold
    Accel Position
    (ACCEL POSITION)
    Accelerator position status:
    Min.: 0 % Max.: 100 %
    1. 0 %:
      Accelerator pedal released
    2. 100 %:
      Accelerator pedal depressed
    Read value with ignition switch on (IG)
    (Do not start engine)
    Vehicle SPD
    (VEHICLE SPD)
    Vehicle speed:
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Stop Light SW
    (STOP LIGHT SW)
    Stop light switch: ON or OFF
    1. ON: Brake pedal depressed
    2. OFF: Brake pedal released
    -
    Elect Load SIG
    (ELECT LOAD SIG)
    Electrical load signal: ON or OFF
    ON: Defogger switch ON
    -
    A/C SIG
    (A/C SIG)
    A/C signal: ON or OFF
    ON: A/C ON
    -
    Starter SIG
    (STARTER SIG)
    Starter signal: ON or OFF
    ON: Cranking
    -
    A/C Cut SIG
    (A/C SIG)
    A/C cut signal: ON or OFF
    ON: A/C cut ON
    -
    MIL Status
    (MIL /WARN LIGHT)
    MIL status: ON or OFF
    ON: MIL illuminated
    -
    #Codes
    (#CODES)
    Number of memorized DTC codes
    0
    -
    Heater Control Lever
    (HTR CTRL LEVER)
    Heater control lever status: HOT or OFF
    HOT: Heater control lever HOT position
    -
    Common Rail Pressure
    (COMN RAIL PRESS)
    Common rail pressure:
    Min.: 0 MPa, Max.: 255 MPa
    25 to 36 MPa: Idling
    -
    Revised Injection Volume #1
    (INJ VOL FB #1)
    Injection volume correction for cylinder 1:
    Min.: -10 mm3, Max.: 40 mm3
    -2.0 to 2.0 mm3: Idling
    -
    Revised Injection Volume #2
    (INJ VOL FB #2)
    Injection volume correction for cylinder 2:
    Min.: -10 mm3, Max.: 40 mm3
    -2.0 to 2.0 mm3: Idling
    -
    Revised Injection Volume #3
    (INJ VOL FB #3)
    Injection volume correction for cylinder 3:
    Min.: -10 mm3, Max.: 40 mm3
    -2.0 to 2.0 mm3: Idling
    -
    Revised Injection Volume #4
    (INJ VOL FB #4)
    Injection volume correction for cylinder 4:
    Min.: -10 mm3, Max.: 40 mm3
    -2.0 to 2.0 mm3: Idling
    -
    M-INJ/PILOT ON
    (M-INJ/PILOT ON)
    M-INJ/PILOT ON:
    Min.: 0 μs, Max.: 65,535 μs
    450 to 750 μs: Idling
    -
    Pilot-Injection
    (PILOT-INJ)
    Pilot-injection:
    Min.: 0 μs, Max.: 65,535 μs
    350 to 550 μs: Idling
    -
    EGR Step POS
    (EGR STEP POS)
    EGR step position status:
    Min.: 0 step, Max.: 108 step
    45 to 65 step: Idling
    -
    Clutch Upper Switch
    (CLUTCH UPPER SW)
    Clutch switch: ON or OFF
    1. ON: Clutch pedal depressed
    2. OFF: Clutch pedal released
    -
    MIL ON Run Distance
    (MIL ON RUN DIST)
    Distance since activation of MIL:
    Min.: 0 km, Max.: 65,535 km
    0 km: When there is no DTC
    -
    *: If no idling conditions are specified, the shift lever should be in the neutral position, the A/C switch and all accessory switches should be OFF.


ACTIVE TEST

HINT:
Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Active Test as a first step of troubleshooting is one method of shortening diagnostic time.
The Data List can be displayed during Active Tests.

  1. Connect an intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Turn the tester on.

  4. Select the following menu items: Powertrain / Engine and ECT / Active Test.

  5. Perform the Active Tests by referring to the following table.

    intelligent tester Display
    Test Details
    Control Range
    Diagnostic Notes
    A/C Cut Signal
    (A/C CUT SIG)
    Control A/C cut signal
    ON/OFF
    -
    EGR Step
    (EGR STEP POS)
    Open or close EGR valve
    From 0 to 108 steps
    1. EGR valve fully closed at step position 0, and fully open at step position 108
    2. Amount of EGR gas, flowing into intake manifold, varies in accordance with EGR valve opening angle
    Fuel leak test
    (FUEL LEAK TEST)
    Pressurize common rail internal fuel pressure, in order to see if fuel leaks
    ON/OFF
    1. Fuel pressure inside common rail pressurized to 135 MPa and engine speed increased to 2,000 rpm when ON selected
    2. Above conditions preserved while test ON
    Injector cut #1
    (INJECTOR CUT #1)
    Cut off fuel injection from No. 1 injector
    ON/OFF
    Fuel injection stopped while test ON
    Injector cut #2
    (INJECTOR CUT #2)
    Cut off fuel injection from No. 2 injector
    ON/OFF
    Injector cut #3
    (INJECTOR CUT #3)
    Cut off fuel injection from No. 3 injector
    ON/OFF
    Injector cut #4
    (INJECTOR CUT #4)
    Cut off fuel injection from No. 4 injector
    ON/OFF

← FAIL-SAFE CHART (from Nov 2005)DIAGNOSTIC TROUBLE CODE CHART (from Nov 2005) →