2005-2008 Yaris · Service Manual ENGINE

REGISTRATION

Other · Vehicles built from Nov 2005

NOTICE:
  1. When an injector is replaced, the injector's compensation code must be input into the ECM (Proceed to step 1).
  2. When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM (Proceed to step 2).


1. INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

NOTICE:
Injector compensation codes are unique, 10-digit, alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

  1. A115972E01
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

    NOTICE:
    Do not start the engine during this operation.

    HINT:
    An injector compensation code is imprinted on the head portion of each injector.

  1. A122614
    Select the following menu items: Powertrain / Engine and ECT / Utility / Injector Compensation.

  1. Press Next.

  1. A122615
    Press Next again to proceed.

  1. A122622
    Select the following menu items: Set Compensation Code.

  1. Press Next.

  1. A122617
    Select the number of the cylinder corresponding to the injector compensation code that you want to read.

  1. Press Next.

  1. A122623
    Register compensation code.

    1. Press input.

    2. A122624
      Manually input the cylinder's compensation code using the keyboard on the tester screen. The code is a 10-digit, alphanumeric value imprinted on the injector's head portion.

      HINT:
      Each injector compensation code is unique. The correct compensation code must be input into each cylinder selected on the tester.

    3. Confirm that the compensation code is correct for the selected cylinder is correct , and then press OK.

  1. A122623
    If a new ECM was installed (and all the injector's compensation codes have been saved in the tester):

    1. Press Open.

    2. A122619
      Press the Open button again to retrieve the saved compensation code.

      HINT:
      If the retrieving process fails, a manual input with the tester is the alternative option. Refer to step (k).

  1. A122625
    Check that the compensation code displayed on the screen is correct, by comparing it with the 10-digit alphanumeric value on the head portion of the injector.

    NOTICE:
    If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

    HINT:
    If a wrong compensation code was input or read, return to the input Value screen by pressing input. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

  1. Press Next to set the compensation code to the ECM.

    HINT:
    1. If the setting process fails, the compensation code may be incorrect. Check the compensation code again.
    2. If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A122626
    If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.

  1. Turn the ignition switch off and then turn the tester off. Turn the tester off and then turn the ignition switch off.

  1. Wait for at least 30 seconds.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear DTC P0603 stored in the ECM using the tester (Click here).


2. INPUT ALL INJECTOR COMPENSATION CODES INTO ECM

NOTICE:
Injector compensation codes are unique, 10-digit, alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

HINT:
The following operation is available with ECMs that can transmit the registered injector compensation codes to the intelligent tester.

  1. A115972E01
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

    NOTICE:
    Do not start the engine during this operation.

    HINT:
    The injector compensation code is imprinted on the head portion of each injector.

  1. A122614
    Select the following menu items: Power train / Engine and ECT / Utility / Injector Compensation.

  1. Press Next.

  1. A122615
    Press Next again to proceed.

  1. A122616
    Select the following menu items: Read Compensation Code.

  1. Press Next.

  1. A122617
    Select the number of the cylinder corresponding to the injector compensation code that you want to read.

  1. Press Next.

    HINT:
    The reading process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A122618
    Check the injector compensation code (10-digit alphanumeric value) displayed on the tester screen.

  1. Press Save.

  1. A122619
    If no injector compensation code for the cylinder exists in the tester.

    1. Check that the compensation code displayed on the tester screen is correct.

    2. Press Save.

      HINT:
      The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A122620
    If another injector compensation code already exists in the tester.

    1. Check that the compensation code displayed on the tester screen is correct.

      HINT:
      The existing compensation code is overwritten with the new compensation code and is deleted from the tester.

    2. Press Replace.

      HINT:
      The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A122618
    If you want to read and save other injector compensation codes for other cylinders, press Next to continue. To finish this operation, press Cancel.

  1. Turn the ignition switch off.

  1. Turn the tester off.

  1. Replace the ECM.

  1. A115972E01
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

    NOTICE:
    Do not start the engine during this operation.

    HINT:
    The injector compensation code is imprinted on the head portion of each injector.

  1. A122614
    Select the following menu items: Powertrain / Engine and ECT / Utility / Injector Compensation.

  1. Press Next.

  1. A122615
    Press Next again to proceed.

  1. A122622
    Select the following menu items: Set Compensation Code.

  1. Press Next.

  1. A122617
    Select the number of the cylinder corresponding to the injector compensation code that you want to read.

  1. Press Next.

  1. A122625
    Check that the compensation code displayed on the screen is correct, by comparing it with the 10-digit alphanumeric value on the head portion of the injector.

    NOTICE:
    If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

    HINT:
    If a wrong compensation code was input or read, return to the input Value screen by pressing input. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

  1. Press Next to set the compensation code to the ECM.

    HINT:
    1. If the setting fails, the compensation code may be incorrect. Check the compensation code again.
    2. If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A122626
    If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.

  1. Turn the ignition switch off and then turn the tester off.

  1. Wait for at least 30 seconds.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear DTC P0603 stored in the ECM using the tester (Click here).

← BASIC INSPECTION (from Nov 2005)PROBLEM SYMPTOMS TABLE (from Nov 2005) →