2005-2008 Yaris · Service Manual STEERING

REMOVAL

Removal / installation · Vehicles built from Aug 2005

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing
(Click here).


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE STEERING PAD (w/o Steering Pad Switch)

C117209E01
  1. Using "Torx" socket wrench T30, loosen the 2 bolts completely.

  1. Pull the steering pad toward you.

  1. C117201E01
    Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, detach the airbag connector.

  1. Detach the horn terminal.


4. REMOVE STEERING PAD (w/ Steering Pad Switch)

C117211E01
  1. Using "Torx" socket wrench T30, loosen the 2 bolts completely.

  1. Pull the steering pad toward you.

  1. C117199E01
    Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, detach the airbag connector.

  1. Detach the horn terminal.


5. REMOVE STEERING WHEEL ASSEMBLY

  1. C117210E01
    Remove the nut and place matchmarks on the steering wheel assembly and steering column assembly.

  1. C117207E01
    Using SST, remove the steering wheel assembly.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of the SST center bolt before using.


6. REMOVE STEERING COLUMN COVER SUPPORT (w/ Entry and Start System)

B108275E01
  1. Disengage the 4 claws and remove the steering column cover support.


7. REMOVE STEERING COLUMN COVER

  1. C117204E01
    Remove the 3 screws, disengage the 2 claws, release the tilt lever and remove the steering column lower cover.

  1. C117205E01
    Disengage the claw and remove the steering column upper cover.


8. REMOVE COMBINATION SWITCH ASSEMBLY
  1. Disconnect all connectors from the turn signal switch with spiral cable.

  1. C117206
    Disengage the clamp indicated by the arrow in the illustration and remove the combination switch assembly from the steering column assembly.


9. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.

  1. E107742E01
    Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.


10. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.

  1. E107744E01
    Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.


11. REMOVE INSTRUMENT CLUSTER FINISH PANEL

B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.

  1. B132364
    Disengage the 2 claws and 5 clips.

  1. B132365E01
    After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.


12. REMOVE COMBINATION METER ASSEMBLY

E107730
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.


13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.


14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for the RH side as for the LH side.


15. REMOVE FRONT PILLAR GARNISH RH

  1. B117693E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B117694
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B114312
    Disconnect the connector.

  1. Using a clip remover, remove the 3 antenna cord clamps.

  1. B127674
    w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.

    2. B127670E01
      Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.

  1. w/ Curtain Shield Airbag:

    1. B114313E01
      Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


16. REMOVE FRONT PILLAR GARNISH LH

  1. B117695E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B117696
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B114316
    Using a clip remover, remove the 4 wire harness clamps.

  1. B127673
    w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.

    2. B127669E01
      Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.

  1. B114317E01
    w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


17. REMOVE SWITCH BASE HOLE COVER

B108201
  1. Disengage the 2 clips and 2 claws and remove the switch hole base.


18. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

B108202
  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.

  1. B105351
    Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.


19. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY UPPER

B108181E02
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.

  1. Remove the 2 <C> bolts and 4 <B> screws.

    B105354E01

  1. Disconnect the connectors.

  1. Disengage the claw and 3 clips while lifting the rear instrument panel up.

  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.

    B105355E01


20. DISCONNECT POWER STEERING ECU

C117192
  1. Detach the power steering motor harness and torque sensor wire harness clamps from the power steering ECU side.

  1. Disconnect the 2 steering column assembly connectors from the power steering ECU.


21. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY NO. 1

  1. B114572
    Remove the 2 screws.

  1. Disengage the 3 claws and remove the instrument panel under cover.


22. REMOVE INSTRUMENT PANEL UNDER TRAY (w/o Driver Side Knee Airbag)

B108185
  1. Disengage the 4 claws and open the instrument panel under tray.

  1. B108187
    Remove the 2 <A> screws.

  1. Disengage the 4 claws and remove the instrument panel under tray.


23. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

C119072E01
  1. Remove the 4 screws.

  1. Disengage the 6 claws and remove the driver side knee airbag assembly.

  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the airbag connector and remove the instrument panel wire.


24. REMOVE COLUMN HOLE COVER SILENCER SHEET

  1. A116501
    Pull back the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.


25. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY NO. 2

G028410E01
  1. Loosen bolt A.

  1. Place matchmarks on the steering intermediate assembly and steering gear assembly.

  1. Remove bolt B and detach the steering intermediate assembly from the steering gear assembly.

  1. Place matchmarks on the steering intermediate assembly and steering column assembly.

  1. Remove bolt C and detach the steering intermediate shaft assembly from the steering column assembly.


26. REMOVE BRAKE PEDAL (for Automatic Transaxle)

C119065
  1. Using needle-nose pliers, remove the brake pedal return spring.

  1. Remove the clip from the brake master cylinder push rod clevis pin.

  1. Remove the brake master cylinder push rod clevis pin and detach the push rod clevis from the brake pedal.

  1. Remove the bolt, nut and 2 brake pedal bushes, and remove the brake pedal assembly.


27. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle)

C116880
  1. Remove the brake pedal return spring.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.


28. REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle)

C116881
  1. Remove the 4 nuts and bolt and remove the pedal support.


29. REMOVE STEERING COLUMN ASSEMBLY
  1. Disconnect all connectors and detach all wire harness clamps from the steering column assembly.

  1. C117203
    Remove the bolt and 2 nuts and remove the steering column assembly from the instrument panel reinforcement assembly.

← COMPONENTS (from Aug 2005)DISASSEMBLY (from Aug 2005) →