2005-2008 Yaris · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL POWER STEERING ECU

  1. C118008
    Install the power steering ECU with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. C117190
    Connect the 4 connectors.

  1. C117191
    Install the wire harness clamp.

    NOTICE:
    Make sure that the wire harness of the steering post assembly is installed onto the power steering ECU bracket and that it is not pulled too tightly.


2. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER

B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.

  1. Engage the claw and the 3 clips at the lower side of the instrument panel.

    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt

  1. Connect the connectors.

    B105354E01

  1. B108182
    Connect the passenger airbag connector and clamp.


3. INSTALL SWITCH BASE HOLE COVER

B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.


4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B108202
    Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.


5. INSTALL FRONT PILLAR GARNISH RH

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127674
      Connect the speaker connector.

  1. B114312
    Install the 3 antenna cord clamps.

  1. Connect the connector.

  1. w/ Curtain Shield Airbag:

    1. B117697E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B117694
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


6. INSTALL FRONT PILLAR GARNISH LH

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127673
      Connect the speaker connector.

  1. B114316
    Install the 4 wire harness clamps.

  1. w/ Curtain Shield Airbag:

    1. B117698E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B114318
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


7. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.


8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for the RH side as for the LH side.


9. INSTALL COMBINATION METER ASSEMBLY

E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.


10. INSTALL INSTRUMENT CLUSTER FINISH PANEL

B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. B132367
    Engage the 4 claws and 5 clips and install the instrument cluster finish panel.


11. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.

  1. E107744
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.


12. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.

  1. E107742
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


14. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT
(Click here)
← REMOVAL (from Aug 2005)COMPONENTS (from Nov 2005) →