TERMINALS OF ECM
System information · Vehicles built from Aug 2005
| ECM |


- HINT:
- Each ECM terminal's standard voltage is shown in the table below.
- In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specific Condition".
- Use the illustration above as a reference for the ECM terminals.
| Symbols (Terminals No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| L (C20-74) - E1 (C20-104) |
V - W |
L shift position switch signal |
Ignition switch on (IG) and shift lever L position |
10 to 14 V |
| Ignition switch on (IG) and shift lever other than L position |
Below 1 V |
|||
| 2 (C20-55) - E1 (C20-104) |
G - W |
2 shift position switch signal |
Ignition switch on (IG) and shift lever 2 position |
10 to 14 V |
| Ignition switch on (IG) and shift lever other than 2 position |
Below 1 V |
|||
| ODMS (A21-26) - E1 (C20-104) |
O - W |
3 shift position switch signal |
Ignition switch on (IG) and shift lever 3 position |
10 to 14 V |
| Ignition switch on (IG) and shift lever other than 3 position |
Below 1 V |
|||
| D (C20-56) - E1 (C20-104) |
L - W |
D shift position switch signal |
Ignition switch on (IG) and shift lever D or 3 position |
10 to 14 V |
| Ignition switch on (IG) and shift lever other than D and 3 positions |
Below 1 V |
|||
| R (C20-53) - E1 (C20-104) |
R - W |
R shift position switch signal |
Ignition switch on (IG) and shift lever R position |
10 to 14 V |
| Ignition switch on (IG) and shift lever other than R position |
Below 1 V |
|||
| N (C20-54) - E1 (C20-104) |
SB - W |
N shift position switch signal |
Ignition switch on (IG) and shift lever N position |
10 to 14 V |
| Ignition switch on (IG) and shift lever other than N position |
Below 1 V |
|||
| P (C20-73) - E1 (C20-104) |
R - W |
P shift position switch signal |
Ignition switch on (IG) and shift lever P position |
10 to 14 V |
| Ignition switch on (IG) and shift lever other than P position |
Below 1 V |
|||
| NT+ (C20-125) - NT- (C20-124) |
B - G |
Speed sensor (NT) signal |
Engine running |
Pulse generation (See waveform 1) |
| STP (A21-36) - E1 (C20-104) |
G - W |
Stop light switch signal |
Brake pedal depressed |
7.5 to 14 V |
| Brake pedal released |
Below 1.5 V |
|||
| SPD (A21-8) - E1 (C20-104) |
V - W |
Speed signal |
Ignition switch on (IG) and driving wheel rotating slowly |
Pulse generation (See waveform 2) |
| S1 (C20-79) - E1 (C20-104) |
SB - W |
S1 solenoid signal |
Ignition switch on (IG) |
10 to 14 V |
| 1st or 2nd gear |
10 to 14 V |
|||
| 3rd or 4th gear |
Below 1 V |
|||
| S2 (C20-78) - E1 (C20-104) |
L - W |
S2 solenoid signal |
Ignition switch on (IG) |
Below 1 V |
| 1st or 4th gear |
10 to 14 V |
|||
| 2nd or 3rd gear |
Below 1 V |
|||
| ST (C20-80) - E1 (C20-104) |
GR - W |
ST solenoid signal |
D position (3rd gear ←→ 4th gear) |
Below 1 V ←→ 10 to 14 V |
| SLT+ (C20-76) - SLT- (C20-75) |
G - W |
SLT solenoid signal |
Engine idling speed |
Pulse generation (See waveform 3) |
| SL (C20-57) - E1 (C20-104) |
P - W |
SL solenoid signal |
Ignition switch on (IG) |
Below 1 V |
| Vehicle driving under lock up range |
10 to 14 V |
|||
| THO1 (C20-72) - ETHO (C20-95) |
Y - B |
ATF (Automatic Transmission Fluid) temperature sensor signal |
ATF temperature: 10°C (50°F) to 145°C (293°F) |
4 to 0 V |
Waveform 1

Terminal
NT+ - NT-
Tool setting
2 V/DIV, 1ms/DIV
Vehicle conditions
Driving at approximately 20 km/h (12 mph )
Waveform 2

Terminal
SPD - E1
Tool setting
2 V/DIV, 20 ms/DIV
Vehicle conditions
Driving at approximately 20 km/h (12 mph)
Waveform 3

Terminal
SLT+ - SLT-
Tool setting
5 V/DIV, 1 ms/DIV
Vehicle conditions
Engine idling speed