DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built from Aug 2005
| EURO-OBD |
When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.
Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in any of the following:

- The emission control system/components
- The power train control components (which affect vehicle emissions)
- The computer
If the malfunction does not recur in 3 consecutive trips, the MIL goes off automatically but the DTCs remain recorded in the ECM memory.- The emission control system/components
To check DTCs, connect the intelligent tester or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle. The scan tool displays DTCs, the freeze frame data and a variety of the engine data.

The DTCs and freeze frame data can be erased with the scan tool (Click here).
| M-OBD (EXCEPT EUROPEAN SPEC.) |
When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.
OBD regulations require that the vehicle's on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in any of the following:

- The emission control system/components
- The power train control components (which affect vehicle emissions)
- The computer
If the malfunction does not recur in 3 consecutive trips, the MIL goes off automatically but the DTCs remain recorded in the ECM memory.- The emission control system/components
| NORMAL MODE AND CHECK MODE |
| 2-TRIP DETECTION LOGIC |
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the ignition switch is turned off and then turned on again, and the same malfunction is detected again, the MIL illuminates.
| FREEZE FRAME DATA |
The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not and whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
The intelligent tester displays freeze frame data recorded at five different points: 1) 3 times before the DTC is set, 2) once when the DTC is set, and 3) once after the DTC is set. The data can be used to simulate the vehicle's condition around the time of the malfunction. The data may be helpful in determining the cause of a malfunction. It may also be helpful in determining whether a DTC is being caused by a temporary malfunction.

| DLC3 (Data Link Connector 3) |
![]() ![]() |
The ECM uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.
Symbols (Terminal No.)
Terminal Description
Condition
Specified Condition
SIL (7) - SG (5)
Bus "+" line
During transmission
Pulse generation
CG (4) - Body ground
Chassis ground
Always
Below 1 Ω
SG (5) - Body ground
Signal ground
Always
Below 1 Ω
BAT (16) - Body ground
Battery positive
Always
10 to 14 V
CANH (6) - CANL (14)
CAN bus line
Ignition switch off*
54 to 69 Ω
CANH (6) - CG (4)
HIGH-level CAN bus line
Ignition switch off*
200 Ω or higher
CANL (14) - CG (4)
LOW-level CAN bus line
Ignition switch off*
200 Ω or higher
CANH (6) - BAT (16)
HIGH-level CAN bus line
Ignition switch off*
6 kΩ or higher
CANL (14) - BAT (16)
LOW-level CAN bus line
Ignition switch off*
6 kΩ or higher
- NOTICE:
- *: Before measuring the resistance, leave the vehicle as is for at least 1 minutes and do not operate the ignition switch, any other switches or the doors.
If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.
| CHECK BATTERY VOLTAGE |
- Standard battery voltage:
- 11 to 14 V
If the voltage is below 11 V, replace the battery before proceeding.
| CHECK MIL |
Check that the MIL illuminates when the ignition switch is turned on (IG).
If the MIL does not illuminate, there is a problem in the MIL circuit (Click here).When the engine is started, the MIL goes off.
