2005-2008 Yaris · Service Manual BRAKE

C0200/31 Right Front Wheel Speed Sensor Signal

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.
C115116E03
DTC No.
DTC Detecting Conditions
Trouble Areas
C0200/31
C0205/32
When any of following conditions detected:
  1. At vehicle speed of 10 km/h (6 mph) or more, open or short in sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of sensor signal from abnormal wheel occurs 255 times or more.
  3. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  4. With IG1 terminal voltage 9.5 V or more, sensor power supply voltage decreases for 0.5 seconds or more.
  5. When vehicle driven at speed of more than 10 km/h (6 mph), one of wheel speeds below one-seventh of other wheel speeds for 15 seconds or more.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1235/35
C1236/36
When either of following conditions detected:
  1. At vehicle speed of 20 km/h (12 mph) or more, noise occurs 75 times or more in sensor signal from abnormal wheel in 5 seconds.
  2. At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.
  1. Front speed sensor (open)
  2. Front speed sensor circuit (open)
C1271/71
C1272/72
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1275/75
C1276/76
Detected only during test mode.
  1. Front speed sensor (open)
  2. Front speed sensor circuit (open)

HINT:
  1. DTCs C0200/31 and C1235/35 relate to the front speed sensor RH.
  2. DTCs C0205/32 and C1236/36 relate to the front speed sensor LH.


WIRING DIAGRAM

C117849E02

INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal in test mode after cleaning or replacement (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector of the speed sensor.Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

    DATA LIST: ABS 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    FR Speed Open
    FR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    FL Speed Open
    FL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


2. READ VALUE OF DATA LIST (FRONT SPEED SENSOR)

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  1. Start the engine and drive the vehicle.

  1. Turn the tester on.

  1. Read the wheel speed value using the intelligent tester.Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

  1. Select the item "FR (FL) Wheel Speed" in the DATA LIST and read the value displayed on the intelligent tester.

    DATA LIST: ABS 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    FR Wheel Speed
    Wheel speed sensor (FR) reading : min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Similar to speed indicated on speedometer
    FL Wheel Speed
    Wheel speed sensor (FL) reading : min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Similar to speed indicated on speedometer

  1. Check that there is no significant difference between the speed value displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    There is almost no difference in the displayed speed values.

    HINT:
    There is a tolerance of +- 10% in the speedometer indication.



NG
Go to step 5
OK


3. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a TEST MODE inspection and check for DTCs (Click here).

    OK:
    No DTC output.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


4. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 11
A

END

5. CHECK FRONT SPEED SENSOR INSTALLATION
  1. Check that the speed sensor installation bolt is tightened properly.

    OK:
    The installation bolt is tightened properly.

Torque:
8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

HINT:
If the installation portion of the sensor is dirty, clean it and reinstall the sensor.



NG
TIGHTEN BOLT PROPERLY
OK


6. CHECK FRONT SPEED SENSOR

  1. BR03795E09
    Visually check the speed sensor for deformation and damage.

    OK:
    No deformation or damage.
    There is no gap between the sensor and front steering knuckle.



NG
REPLACE FRONT SPEED SENSOR
OK


7. CHECK SPEED SENSOR TIP
  1. Remove the front speed sensor.

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.



NG
CLEAN OR REPLACE SPEED SENSOR
OK


8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
  1. Confirm that the skid control ECU connector and front speed sensor connector are properly connected.

  1. Disconnect the skid control ECU connector and the front speed sensor connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. C117857E03
    Measure the resistance.

    Standard Resistance (LH):
    Tester Connection
    Specified Condition
    A15-9 (FL+) - A11-2 (FL+)
    Below 1 Ω
    A15-8 (FL-) - A11-1 (FL-)
    Below 1 Ω

    Standard Resistance (RH):
    Tester Connection
    Specified Condition
    A15-31 (FR+) - A7-2 (FR+)
    Below 1 Ω
    A15-30 (FR-) - A7-1 (FR-)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT FRONT SPEED SENSOR (INPUT VOLTAGE)
  1. Disconnect the front speed sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A11-2 (FL+) - Body ground
    Ignition switch on
    5.7 to 17.3 V
    A7-2 (FR+) - Body ground
    Ignition switch on
    5.7 to 17.3 V



NG
REPLACE BRAKE ACTUATOR
OK


10. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


11. REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor.


NEXT


12. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR


← ON-VEHICLE INSPECTION (from Aug 2005)C0210/33 Right Rear Wheel Speed Sensor Signal (+ 7 more codes) (from Aug 2005) →