2005-2008 Yaris · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using an intelligent tester.
Signals
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection conditions
Trouble Areas
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch on (IG)
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. STOP fuse
  4. IGN fuse
  5. ECM

WIRING DIAGRAM

A115678E01

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. STP signal conditions can be checked using an intelligent tester.
    1. Connect an intelligent tester to the DLC3.
    2. Turn the ignition switch on (IG) and turn the tester on.
    3. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
    4. Check the STP signal when the brake pedal is depressed and released.
      Brake Pedal Operation
      Specified Conditions
      Depressed
      STP signal ON
      Released
      STP signal OFF


1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
A115660E01
  1. Disconnect the A13 stop light switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals ST1- and STP of the A13 stop light switch connector and the body ground.

    Standard Voltage:
    9 to 14 V

  1. Reconnect the stop light switch connector.



NG
Go to step 4
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
A115657E03
  1. Remove the stop light switch assembly.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Switch Positions
    Specified Conditions
    1 - 2
    Switch pin released
    Below 1 Ω
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin released
    10 kΩ or higher
    Switch pin pushed in
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3. CHECK ECM (STP AND ST1 - VOLTAGE)
A112585E01
  1. Disconnect the A21 ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals ST1- and STP of the A21 ECM connector and body ground.

Standard voltage:
Tester Connections
Brake Pedal Operations
Specified Conditions
ST1- (A21-35) - Body ground
Released
9 to 14 V
Depressed
0 to 3 V
STP (A21-36) - Body ground
Released
0 to 3 V
Depressed
9 to 14 V

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

4. INSPECT FUSE (STOP AND IGN FUSE)
A112611E02
  1. Remove the STOP and IGN fuses from the main body ECU.

  1. Check the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the STOP and IGN fuses.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0500 Vehicle Speed Sensor "A" (from Jan 2006)P0505 Idle Control System Malfunction (from Aug 2005) →