P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built from Nov 2005
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.- HINT:
- The normal conditions are as shown in the table below. The signals can be read using an intelligent tester.
Signals
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
| DTC No. |
DTC Detection Conditions |
Trouble Areas |
| P0504 |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch on (IG) (b) Brake pedal released (c) STP signal OFF when ST1- signal OFF |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- STP signal conditions can be checked using an intelligent tester.
- Connect an intelligent tester to the DLC3.
- Turn the ignition switch on (IG) and turn the tester on.
- Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
- Check the STP signal when the brake pedal is depressed and released.
Brake Pedal Operation
Specified Conditions
Depressed
STP signal ON
Released
STP signal OFF
- Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
![]() ![]() |
Disconnect the A13 stop light switch connector.
Turn the ignition switch on (IG).
Measure the voltage between the terminals ST1- and STP of the A13 stop light switch connector and body ground.
- Standard Voltage:
- 9 to 14 V
Reconnect the stop light switch connector.
|
|
||||
| OK | |
| 2. INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() ![]() |
Remove the stop light switch assembly.
Check the resistance.
- Standard resistance:
Tester Connections
Switch Positions
Specified Conditions
1 - 2
Switch pin released
Below 1 Ω
Switch pin pushed in
10 kΩ or higher
3 - 4
Switch pin released
10 kΩ or higher
Switch pin pushed in
Below 1 Ω
Reinstall the stop light switch assembly.
|
|
||||
| OK | |
| 3. CHECK ECM (STP AND ST1 - VOLTAGE) |
![]() ![]() |
Disconnect the A21 ECM connector.
Turn the ignition switch on (IG).
Measure the voltage between the terminals ST1- and STP of the A21 ECM connector and body ground.
- Standard voltage:
Tester Connections
Brake Pedal Operations
Specified Conditions
ST1- (A21-35) - Body ground
Released
9 to 14 V
Depressed
0 to 3 V
STP (A21-36) - Body ground
Released
0 to 3 V
Depressed
9 to 14 V
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (STOP AND IGN FUSE) |
![]() ![]() |
Remove the STOP and IGN fuses from the main body ECU.
Check the resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the STOP and IGN fuses.
|
|
||||
| OK | ||
| ||




