DISASSEMBLY
Removal / installation · Vehicles built from Aug 2005
| 1. REMOVE MANUAL TRANSAXLE CASE PLUG |
![]() ![]() |
Remove the manual transaxle case plug and gasket from the manual transaxle case.
| 2. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ Speedometer Driven Hole Cover) |
![]() ![]() |
Remove the bolt and speedometer driven hole cover from the transaxle case.
| 3. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY |
Separate the back-up light switch wire harness from the 2 clamps.

Using SST, remove the back-up light switch and gasket from the manual transmission case.

- SST
- 09817-16011
| 4. REMOVE CONTROL CABLE BRACKET |
![]() ![]() |
Remove the 2 bolts and the control cable bracket.
| 5. REMOVE SHIFT GATE PIN |
![]() ![]() |
Remove the shift gate pin from the manual transmission case.
| 6. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY |
![]() ![]() |
Remove the 4 bolts and shift and select lever shaft from the transmission case.
Remove the select return compression spring from the transmission case.
| 7. REMOVE REVERSE IDLER GEAR SHAFT BOLT |
![]() ![]() |
Remove the reverse idler gear shaft bolt and gasket.
| 8. REMOVE MANUAL TRANSMISSION CASE |
![]() ![]() |
Remove the 5 bolts from the manual transaxle case side.
Remove the 8 bolts from the manual transmission case side.

Using a plastic hammer, remove the manual transmission case.
| 9. REMOVE REVERSE IDLER GEAR SHAFT |
![]() ![]() |
Remove the reverse idler gear shaft from the transaxle case.
| 10. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY |
Remove the reverse idler gear from the transaxle case.
| 11. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY |
![]() ![]() |
Remove the 2 bolts and the reverse shift arm bracket from the front transaxle case.
| 12. REMOVE GEAR SHIFT FORK SHAFT NO.1 |
![]() ![]() |
Remove the bolt from gear shift fork No. 1.
Using a pin punch and hammer, remove the slotted spring pin from gear shift head No. 1.

Remove gear shift fork shaft No. 1, gear shift head No. 1 and gear shift fork No. 1.

Using 2 screwdrivers and a hammer, remove the snap ring from gear shift fork shaft No. 1.

| 13. REMOVE GEAR SHIFT FORK SHAFT NO.3 |
![]() ![]() |
Remove the straight pin from gear shift fork No. 3.
Using a pin punch and hammer, remove the slotted spring pin from gear shift head No. 3.

Using 2 screwdrivers and a hammer, remove the snap ring from gear shift fork shaft No. 3.

- HINT:
- Use a shop rag or piece of cloth to prevent the snap ring from flying off.
Remove gear shift fork shaft No. 3, the compression spring, gear shift head No. 3 and gear shift fork No. 3 from the front transaxle case.

Using 2 screwdrivers and a hammer, remove the snap ring from gear shift fork shaft No. 3.

- HINT:
- Use a shop rag or piece of cloth to prevent the snap ring from flying off.
| 14. REMOVE GEAR SHIFT FORK SHAFT NO.2 |
![]() ![]() |
Using a magnetic finger, remove the straight pin from the reverse shift fork.
Using 2 screwdrivers and a hammer, remove the snap ring from gear shift fork shaft No. 3.

- HINT:
- Use a shop rag or piece of cloth to prevent the snap ring from flying off.
Remove the bolt from gear shift fork No. 2.

Shift gear shift fork No. 2 to the 4th gear range.

Remove gear shift fork shaft No. 2, gear shift fork No. 2 and the reverse shift fork.
Using 2 screwdrivers and a hammer, remove the snap ring from gear shift fork shaft No. 2.

- HINT:
- Use a shop rag or piece of cloth to prevent the snap ring from flying off.
| 15. REMOVE INPUT SHAFT ASSEMBLY |
![]() ![]() |
Remove the input shaft assembly from the manual transaxle case.
| 16. REMOVE OUTPUT SHAFT ASSEMBLY |
Remove the output shaft assembly from the manual transaxle case.
| 17. REMOVE DIFFERENTIAL CASE ASSEMBLY |
![]() ![]() |
Remove the differential case assembly from the front transaxle case.
| 18. REMOVE OIL RECEIVER PIPE NO. 2 |
![]() ![]() |
Remove oil receiver pipe No. 2 from the manual transmission case.
- NOTICE:
- Do not damage oil receiver pipe No. 2.
| 19. REMOVE TRANSMISSION MAGNET |
![]() ![]() |
Remove the transmission magnet from the front transaxle case.
| 20. REMOVE FRONT TRANSAXLE CASE OIL SEAL |
![]() ![]() |
Using a screwdriver, remove the front transaxle case oil seal.
| 21. REMOVE OUTPUT SHAFT FRONT BEARING |
![]() ![]() |
Using SST, remove the output shaft front bearing (outer race) from the front transaxle case.
- SST
- 09308-00010
| 22. REMOVE OUTPUT SHAFT COVER |
![]() ![]() |
Remove the output shaft cover from the transaxle case.
| 23. REMOVE TRANSMISSION CASE OIL SEAL |
![]() ![]() |
Using a screwdriver, remove the transmission case oil seal.
| 24. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() ![]() |
Using SST, remove the front differential case rear tapered roller bearing and the shim.
- SST
- 09950-60010
(09951-00560)
09950-70010 (09951-07200)
| 25. REMOVE TRANSAXLE CASE OIL SEAL |
![]() ![]() |
Using a screwdriver, remove the transaxle case oil seal from the transaxle case.
| 26. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() ![]() |
Using a brass bar and a hammer, remove the front differential case front tapered roller bearing.
| 27. REMOVE INPUT SHAFT REAR BEARING SHIM |
![]() ![]() |
Remove the input shaft rear bearing shim from the transmission case.
| 28. REMOVE OUTPUT SHAFT REAR BEARING |
![]() ![]() |
Using SST, remove the output shaft rear bearing.
- SST
- 09527-30010
09612-65014 (09612-01030, 09612-01050)
| 29. REMOVE OUTPUT SHAFT REAR BEARING SHIM |
![]() ![]() |
Remove the output shaft rear bearing shim.


























