REASSEMBLY
Removal / installation · Vehicles built from Nov 2005
| 1.
INSTALL INPUT SHAFT FRONT BEARING |
 |
Using SST and a press, install a new input shaft front bearing onto the input shaft.
- SST
- 09515-10010
| 2.
INSTALL 3RD GEAR NEEDLE ROLLER BEARING |
 |
Coat the 3rd gear needle roller bearing with gear oil, and install it onto the input shaft.
| 3.
INSTALL 3RD GEAR |
 |
Coat the 3rd gear with gear oil, and install it onto the input shaft.
| 4.
INSTALL 3RD GEAR SYNCHRONIZER RING |
 |
Coat the 3rd gear synchronizer ring with gear oil, and install it onto the 3rd gear.
| 5.
INSTALL TRANSMISSION CLUTCH HUB NO.2 |
 |
Install the 3 shifting keys No. 2, 2 shifting key springs and transmission hub sleeve No. 2 onto the clutch hub No. 2.
- NOTICE:
- Assemble the transmission hub sleeve No. 2 and transmission clutch hub No. 2 in the correct orientations, as shown in the illustration.
- Using SST and a press, install the transmission clutch hub sleeve No. 2 onto the input shaft.
- SST
- 09506-35010
| 6.
INSTALL CLUTCH HUB NO.2 SETTING SHAFT SNAP RING |
 |
Select a snap ring that allows the minimum axial play.
- Standard clearance:
- 0.1 mm (0.0039 in.) or less.
Mark
|
Thickness mm (in.)
|
Mark
|
Thickness mm (in.)
|
A
|
2.28 (0.0898)
|
D
|
2.46 (0.0969)
|
B
|
2.34 (0.0921)
|
E
|
2.52 (0.0992)
|
C
|
2.40 (0.0945)
|
F
|
2.58 (0.1016)
|
- Using a snap ring expander, install the new snap ring onto the input shaft.
- HINT:
- Do not damage the journal surface of the input shaft.
| 7.
INSPECT 3RD GEAR THRUST CLEARANCE |
 |
Using a feeler gauge, measure the 3rd gear thrust clearance.
- Standard clearance:
- 0.10 to 0.35 mm (0.0039 to 0.0138 in.)
- Maximum clearance:
- 0.35 mm (0.0138 in.)
If the clearance exceeds the maximum, replace the 3rd gear synchronizer ring.
| 8.
INSPECT 3RD GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the 3rd gear radial clearance.
- Standard clearance:
- 0.015 to 0.058 mm (0.0006 to 0.0023 in.)
- Maximum clearance:
- 0.058 mm (0.0023 in.)
If the clearance exceeds the maximum, replace the 3rd gear needle roller bearing or the shaft.
| 9.
INSTALL 4TH GEAR SYNCHRONIZER RING |
 |
Coat the 4th gear synchronizer ring with gear oil, and install it onto transmission clutch hub No. 2.
| 10.
INSTALL 4TH GEAR BEARING SPACER |
 |
Coat the 4th gear bearing spacer with gear oil, and install it onto the input shaft.
| 11.
INSTALL 4TH GEAR NEEDLE ROLLER BEARING |
 |
Coat the 4th gear needle roller bearing with gear oil, and install it onto the input shaft.
| 12.
INSTALL 4TH GEAR |
 |
Coat the 4th gear with gear oil, and install it onto the input shaft.
| 13.
INSTALL 5TH GEAR THRUST WASHER BALL |
 |
Install the 5th gear thrust washer ball onto the input shaft.
| 14.
INSTALL 5TH GEAR THRUST WASHER |
 |
Coat the 5th gear thrust washer with gear oil, and install it onto the input shaft.
| 15.
INSTALL 5TH GEAR SHAFT SNAP RING |
 |
Select a snap ring, using the table below, that makes the thrust clearance of the 5th gear thrust washer less than 0.1 mm (0.0039 in.).
Mark
|
Thickness mm (in.)
|
Mark
|
Thickness mm (in.)
|
1
|
2.28 (0.0898)
|
4
|
2.46 (0.0969)
|
2
|
2.34 (0.0921)
|
5
|
2.52 (0.0992)
|
3
|
2.40 (0.0945)
|
6
|
2.58 (0.1016)
|
- Using a snap ring expander, install a new snap ring onto the input shaft.
- HINT:
- Do not damage the journal surface of the input shaft.
| 16.
INSPECT 4TH GEAR THRUST CLEARANCE |
 |
Using a dial indicator, measure the 4th gear thrust clearance.
- Standard clearance:
- 0.1 to 0.55 mm (0.0039 to 0.0217 in.)
- Maximum clearance :
- 0.55 mm (0.0217 in.)
If the clearance exceeds the maximum, replace the 4th gear synchronizer ring.
| 17.
INSPECT 4TH GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the 4th gear radial clearance.
- Standard clearance:
- 0.015 to 0.058 mm (0.0006 to 0.0023 in.)
- Maximum clearance:
- 0.058 mm (0.0023 in.)
If the clearance exceeds the maximum, replace the 4th gear needle roller bearing or the shaft.
| 18.
INSTALL 5TH GEAR BEARING SPACER |
 |
Coat the 5th gear bearing spacer with gear oil, and install it onto the input shaft.
| 19.
INSTALL 5TH GEAR NEEDLE ROLLER BEARING |
 |
Coat the 5th gear needle roller bearing with gear oil, and install it onto the input shaft.
| 20.
INSTALL 5TH GEAR |
 |
Coat the 5th gear with gear oil, and install it onto the input shaft.
| 21.
INSTALL 5TH GEAR SYNCHRONIZER RING |
 |
Coat the 5th gear synchronizer ring with gear oil, and install it onto the 5th gear.
| 22.
INSTALL TRANSMISSION CLUTCH HUB NO.3 |
 |
Install the 3 shifting keys No. 3, 2 shifting key springs No. 1 and transmission hub sleeve No. 3 onto the transmission clutch hub No. 3.
- NOTICE:
- Assemble the transmission hub sleeve No. 3 and the transmission clutch hub No. 3 in the correct orientations, as shown in the illustration.
Place the 5th gear synchronizer ring on the 5th gear, and align the synchronizer ring slots with the shifting keys No. 3.
- Using SST and a press, press the No. 3 hub sleeve into the input shaft.
- SST
- 09515-10010
- NOTICE:
- Install the transmission hub sleeve No. 3 in the correct orientation, as shown in the illustration.
| 23.
INSTALL INPUT SHAFT REAR RADIAL BALL BEARING |
 |
Using SST and a press, install a new input shaft rear radial ball bearing onto the input shaft.
- SST
- 09515-10010
| 24.
INSPECT 5TH GEAR THRUST CLEARANCE |
 |
Using a dial indicator, measure the 5th gear thrust clearance.
- Standard clearance:
- 0.10 to 0.50 mm (0.0039 to 0.0197 in.)
- Maximum clearance:
- 0.50 mm (0.0197 in.)
If the clearance exceeds the maximum, replace the 5th gear synchronizer ring.
| 25.
INSPECT 5TH GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the 5th gear radial clearance.
- Standard clearance:
- 0.015 to 0.058 mm (0.0006 to 0.0023 in.)
- Maximum clearance:
- 0.058 mm (0.0023 in.)
If the clearance exceeds the maximum, replace the 5th gear needle roller bearing or the shaft.