DISASSEMBLY
Removal / installation · Vehicles built from Aug 2005
| 1.
REMOVE OUTPUT SHAFT REAR BEARING |
 |
Using SST and a press, remove the output shaft rear bearing.
- SST
- 09950-60010
(09951-00220)
09950-70010
(09951-07100)
| 2.
INSPECT 1ST GEAR THRUST CLEARANCE |
 |
Using a feeler gauge, measure the 1st gear thrust clearance.
- Standard clearance:
- 0.10 to 0.45 mm (0.0039 to 0.0177 in.)
- Maximum clearance:
- 0.45 mm (0.0177 in.)
If the clearance exceeds the maximum, replace the 1st gear synchronizer ring.
| 3.
INSPECT 2ND GEAR THRUST CLEARANCE |
 |
Using a feeler gauge, measure the 2nd gear thrust clearance.
- Standard clearance:
- 0.10 to 0.55 mm (0.0039 to 0.0217 in.)
- Maximum clearance:
- 0.55 mm (0.0217 in.)
If the clearance exceeds the maximum, replace the 2nd gear synchronizer ring.
| 4.
INSPECT 1ST GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the 1st gear radial clearance.
- Standard clearance:
- 0.015 to 0.056 mm (0.0006 to 0.0022 in.)
- Maximum clearance:
- 0.056 mm (0.0022 in.)
If the clearance exceeds the maximum, replace the 1st gear needle roller bearing or the shaft.
| 5.
INSPECT 2ND GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the 2nd gear radial clearance.
- Standard clearance:
- 0.015 to 0.056 mm (0.0006 to 0.0022 in.)
- Maximum clearance:
- 0.056 mm (0.0022 in.)
If the clearance exceeds the maximum, replace the 2nd gear needle roller bearing or the shaft.
| 6.
REMOVE COUNTER 5TH GEAR SHAFT SNAP RING |
 |
Using 2 screwdrivers and a hammer, remove the counter 5th gear shaft snap ring from the output shaft.
| 7.
REMOVE 4TH DRIVEN GEAR |
 |
Using a press, remove the 5th driven gear and 4th driven gear from the output shaft.
| 8.
REMOVE OUTPUT SHAFT SPACER |
 |
Remove the output shaft spacer from the output shaft.
| 9.
REMOVE 2ND GEAR |
 |
Using SST and a press, remove the 3rd driven gear and 2nd gear from the output shaft.
- SST
- 09950-00020
| 10.
REMOVE 2ND GEAR NEEDLE ROLLER BEARING |
 |
Remove the 2nd gear needle roller bearing from the output shaft.
| 11.
REMOVE 2ND GEAR BEARING SPACER |
 |
Remove the 2nd gear bearing spacer from the output shaft.
| 12.
REMOVE 2ND GEAR SYNCHRONIZER RING |
 |
Remove the 2nd gear synchronizer ring from the reverse gear.
| 13.
REMOVE CLUTCH HUB NO.1 SHAFT SNAP RING |
 |
Using 2 screwdrivers, remove the clutch hub No. 1 shaft snap ring from the output shaft.
- HINT:
- Do not damage the journal surface of the output shaft.
| 14.
REMOVE 1ST GEAR |
 |
Using a press, remove transmission clutch hub No. 1 and the 1st gear from the output shaft.
| 15.
REMOVE 1ST GEAR NEEDLE ROLLER BEARING |
 |
Remove the 1st gear needle roller bearing from the output shaft.
| 16.
REMOVE OUTPUT SHAFT FRONT BEARING |
 |
Using SST and a press, remove the output shaft front bearing from the output shaft.
- SST
- 09950-00020
| 17.
REMOVE TRANSMISSION CLUTCH HUB NO.1 |
 |
Remove the 2 shifting key springs No. 1, 3 shifting keys No. 1 and reverse gear from transmission clutch hub No. 1.