2005-2008 Yaris · Service Manual ENGINE

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Nov 2005


ENTRY AND START DESCRIPTION
  1. The entry and start uses a push-type ignition switch, which the driver can operate by merely carrying the key. This system consists primarily of the main body ECU, ignition switch, ID code box, steering lock ECU, key, ACC CUT relay, IG1 relay, IG2 relay and certification ECU. The main body ECU controls the system. This function operates in cooperation with the entry and start system. The table below shows the transition of the ignition switch, which depends on whether the clutch pedal is depressed or released.

  2. This system has different power source mode patterns depending on the clutch pedal conditions.

    For M/T: 
    Clutch Pedal
    Power Source Mode Pattern
    Not depressed
    Each time ignition switch is pushed
    1. off → on (ACC) → on (IG) → off
    Not depressed
    When ignition switch is pushed in the engine started condition
    1. Engine started → off
    Depressed
    When ignition switch is pushed once
    1. off → engine start
    Depressed
    When ignition switch is pushed in the on (ACC) condition
    1. on (ACC) → engine start
    Depressed
    When ignition switch is pushed in the on (IG) condition
    1. on (IG) → engine start
    Depressed
    When ignition switch is pushed in the engine started condition
    1. Engine started → off
    For except M/T: 
    Brake Pedal
    Shift Lever
    Power Source Mode Pattern
    Depressed
    N Position
    1. When the engine switch is pushed once.
      1. OFF → IG ON (after the engine is started)
    Not Depressed
    N Position
    1. Each time the engine switch is pushed.
      1. OFF → ACC → IG ON → OFF
    Except N Position
    1. Each time the engine switch is pushed.
      1. OFF → ACC → IG ON → OFF
    -
    N Position
    1. When the engine switch is pushed in the IG-ON condition.
      1. IG ON (engine is started or not started) → OFF
    -
    Except N Position
    1. When the engine switch is pushed in the IG-ON condition.
      1. IG ON (engine is started or not started) → OFF
    When the battery of the key is low, the entry and start function can be operated by holding the key against the ignition switch.


FUNCTION OF COMPONENT
Components
Function
Ignition Switch
(Transponder Key Amplifier)
  1. Transmits ignition switch signal to main body ECU.
  2. Informs driver of power source mode or system abnormality with indicator light illumination.
  3. Receives ID code and transmits it to certification ECU when battery of key is low.
Key
  1. Receives signals from oscillators and returns ID code to entry door control receiver.
Indoor Electrical Key Oscillator
(Front and Rear)
  1. Receives request signal from certification ECU and forms detection area in vehicle interior.
Entry Door Control Receiver
  1. Receives ID code from key and transmits it to certification ECU.
Main Body ECU
  1. Changes power source mode in 4 stages (off, on (ACC), on (IG), start) in accordance with state of clutch start switch or park/neutral start switch.
  2. Controls entry and start function in accordance with signals received from switches and each ECU.
Certification ECU
  1. Certifies ID code received from entry door control receiver and transmits certification results to ID code box and steering lock ECU.
Stop Light Switch
  1. Outputs state of brake pedal to main body ECU.
Clutch Start Switch
  1. Outputs state of clutch pedal to main body ECU.
ID Code Box
  1. Receives steering unlock or engine immobiliser unset signals from certification ECU, certifies them, and transmits each unset signal to steering lock ECU or ECM.
ECM
  1. Receives engine start request signal from power source control ECU, turns ON ST relay, and starts engine.
  2. Receives signal from immobiliser code ECU and performs engine ignition and injection.

SYSTEM FUNCTION
The electric controls of the entry and start function are described below:
Control
Outline
Ignition Switch Control
  1. When driver operates ignition switch with key in driver's possession, certification ECU starts indoor electrical key oscillator, which transmits request signal to key. Upon receiving this signal, key transmits ID code signal to main body ECU.
  2. ID code box verifies check results received from certification ECU via LIN and sends them to main body ECU. Based on these results, main body ECU authorizes operation of ignition switch.
Diagnosis
  1. When main body ECU detects malfunction, main body ECU diagnoses and memorizes failed section.

CONSTRUCTION AND OPERATION
A109251E01
  1. Ignition Switch
    Ignition switch consists of a momentary type switch, 3 color (amber, green, greenish white) LEDs, and transponder key amplifier.

    1. The greenish white LED is for illumination.
    2. The amber and green LEDs are for the indicator lights. The driver can check the present power source mode and whether the engine can start or not in accordance with the illumination state of the indicator light.
    3. When the main body ECU detects an abnormality in the entry and start system, it makes the amber indicator light flash. If the engine stopped in this state, it might not be possible to restart it.

  2. Indicator Light Condition

    Ignition switch indicator light condition 
    Power Source Mode/Condition
    Indicator Light Condition
    Clutch pedal released (M/T)
    Brake pedal released (except M/T)
    Clutch pedal depressed (M/T)
    Brake pedal depressed (except M/T)
    Off
    OFF
    Illuminates (Green)
    On (ACC, IG)
    Illuminates (Amber)
    Illuminates (Green)
    Engine running
    OFF
    OFF
    Steering lock not unlocked
    Flashes (Green) for 15 seconds
    Flashes (Green) for 15 seconds
    System malfunction
    Flashes (Amber) for 15 seconds
    Flashes (Amber) for 15 seconds
    Clutch switch malfunction (M/T)
    Flashes (Green) for 15 seconds
    Flashes (Green) for 15 seconds

  3. Main Body ECU
    The main body ECU consists of the IG1 and IG2 relay actuation circuits and CPU.


WHEN KEY BATTERY IS LOW
B122856E02
  1. To operate the entry and start function when the key battery is low, hold the TOYOTA mark of the key against the ignition switch while depressing the brake pedal.

  2. The main body ECU transmits a key verification request signal from the stop light switch to the certification ECU.

  3. The certification ECU does not receive an ID code response from the smart tuner, so it actuates the transponder key amplifier built into the ignition switch.

  4. The transponder key amplifier outputs an engine immobiliser radio wave to the key.

  5. The key receives the radio wave, and returns a radio wave response to the transponder key amplifier.

  6. The transponder key amplifier combines the key ID codes with the radio wave response, and transmits it to the certification ECU.

  7. The certification ECU judges and verifies the ID code, and transmits a key verification OK signal to the main body ECU. The buzzer in the combination meter sounds at the same time.

  8. After the buzzer sounds, if the ignition switch is pressed within 5 seconds with the brake pedal not depressed, the power source mode changes to on (ACC) or on (IG), the same as in the normal condition.


DIAGNOSIS
The main body ECU can detect malfunctions in the entry and start function when the power source mode is on (IG).
When the ECU detects a malfunction, the amber indicator light of the ignition switch flashes to warn the driver. At the same time, the ECU stores the 5-digit DTC (Diagnostic Trouble Code) in the memory.
  1. The indicator light warning continues for 15 seconds even after the power source mode is changed to off.
  2. The DTC can be read by connecting the intelligent tester to the DLC3.
  3. The entry and start function cannot be operated if a malfunction occurs.
← SYSTEM DIAGRAM (from Nov 2005)HOW TO PROCEED WITH TROUBLESHOOTING (from Nov 2005) →