SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Nov 2006
| ENTRY AND START DESCRIPTION |
The entry and start uses a push-type engine switch, which the driver can operate by merely carrying the key. This system consists primarily of the main body ECU, engine switch, ID code box, steering lock ECU, key, ACC CUT relay, IG1 relay, IG2 relay and certification ECU. The main body ECU controls the system. This function operates in cooperation with the entry and start system. The table below shows the transition of the engine switch, which depends on whether the clutch pedal is depressed or released.
This system has different power source mode patterns depending on the clutch pedal conditions.
When the battery of the key is low, the entry and start function can be operated by holding the key against the engine switch.Clutch Pedal
Power Source Mode Pattern
Not depressed
Each time engine switch is pushed - off → on (ACC) → on (IG) → off
Not depressed
When engine switch is pushed in the engine started condition - Engine started → off
Depressed
When engine switch is pushed once - off → engine start
Depressed
When engine switch is pushed in the on (ACC) condition - on (ACC) → engine start
Depressed
When engine switch is pushed in the on (IG) condition - on (IG) → engine start
Depressed
When engine switch is pushed in the engine started condition - Engine started → off
- off → on (ACC) → on (IG) → off
| FUNCTION OF COMPONENT |
| Components |
Function |
| Engine Switch (Transponder Key Amplifier) |
|
| Key |
|
| Indoor Electrical Key Oscillator (Front and Rear) |
|
| Entry Door Control Receiver |
|
| Main Body ECU |
|
| Certification ECU |
|
| Clutch Start Switch |
|
| ID Code Box |
|
| ECM |
|
| SYSTEM FUNCTION |
| Control |
Outline |
| Engine Switch Control |
|
| Diagnosis |
|
| CONSTRUCTION AND OPERATION |
![]() ![]() |
Engine Switch
Engine switch consists of a momentary type switch, 3 color (amber, green, greenish white) LEDs, and transponder key amplifier.- The greenish white LED is for illumination.
- The amber and green LEDs are for the indicator lights. The driver can check the present power source mode and whether the engine can start or not in accordance with the illumination state of the indicator light.
- When the main body ECU detects an abnormality in the entry and start system, it makes the amber indicator light flash. If the engine stopped in this state, it might not be possible to restart it.
- The greenish white LED is for illumination.
Indicator Light Condition
Engine switch indicator light condition Power Source Mode/Condition
Indicator Light Condition
Clutch pedal released
Clutch pedal depressed
Off
OFF
Illuminates (Green)
On (ACC, IG)
Illuminates (Amber)
Illuminates (Green)
Engine running
OFF
OFF
Steering lock not unlocked
Flashes (Green) for 15 seconds
Flashes (Green) for 15 seconds
System malfunction
Flashes (Amber) for 15 seconds
Flashes (Amber) for 15 seconds
Clutch switch malfunction
Flashes (Green) for 15 seconds
Flashes (Green) for 15 seconds
Main Body ECU
The main body ECU consists of the IG1 and IG2 relay actuation circuits and CPU.
| WHEN KEY BATTERY IS LOW |
To operate the entry and start function when the key battery is low, hold the TOYOTA mark of the key against the engine switch while depressing the clutch pedal.

The main body ECU transmits a key verification request signal from the clutch pedal switch to the certification ECU.
The certification ECU does not receive an ID code response from the smart tuner, so it actuates the transponder key amplifier built into the engine switch.
The transponder key amplifier outputs an engine immobiliser radio wave to the key.
The key receives the radio wave, and returns a radio wave response to the transponder key amplifier.
The transponder key amplifier combines the key ID codes with the radio wave response, and transmits it to the certification ECU.
The certification ECU judges and verifies the ID code, and transmits a key verification OK signal to the main body ECU. The buzzer in the combination meter sounds at the same time.
After the buzzer sounds, if the engine switch is pressed within 5 seconds with the clutch pedal not depressed, the power source mode changes to on (ACC) or on (IG), the same as in the normal condition.
| DIAGNOSIS |
When the ECU detects a malfunction, the amber indicator light of the engine switch flashes to warn the driver. At the same time, the ECU stores the 5-digit DTC (Diagnostic Trouble Code) in the memory.
- The indicator light warning continues for 15 seconds even after the power source mode is changed to off.
- The DTC can be read by connecting the intelligent tester to the DLC3.
- The entry and start function cannot be operated if a malfunction occurs.
