2005-2008 Yaris · Service Manual HEATER & AIR CONDITIONING SYSTEM

REMOVAL

Removal / installation · Vehicles built from Aug 2005


1. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.

  1. E107742E01
    Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.


2. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.

  1. E107744E01
    Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.


3. REMOVE INSTRUMENT CLUSTER FINISH PANEL

B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.

  1. B132364
    Disengage the 2 claws and 5 clips.

  1. B132365E01
    After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.


4. REMOVE RADIO RECEIVER ASSEMBLY (w/ CD Player)

E116821E01
  1. Remove the 4 screws.

  1. Disengage the 2 claws and 4 clips and the radio receiver.

    NOTICE:
    1. Grip the rib portion of the radio receiver by hand to remove it.
    2. To avoid breakage of the radio receiver when removing it, do not apply excessive force to the register or pull out the rink or panel portions.

  1. Disconnect the connectors.


5. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER (Except CD Player)

B132368E01
  1. Disengage the 2 claws and 4 clips and the instrument cluster finish panel center.

    NOTICE:
    1. Grip the rib portion of the instrument cluster finish panel center by hand to remove it.
    2. To avoid breakage of the instrument cluster finish panel center when removing it, do not apply excessive force to the register or pull out the rink or panel portions.


6. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

I101591
  1. Disengage the 3 clips and 2 claws and remove the air conditioning control assembly.

  1. I101169
    Disconnect the 2 connectors, clamp and the aspirator pipe.


7. REMOVE ROOM TEMPERATURE SENSOR

I101586
  1. Disengage the 2 claws and remove the room temperature sensor.

← COMPONENTS (from Aug 2005)DISASSEMBLY (from Aug 2005) →