2005-2008 Yaris · Service Manual HEATER & AIR CONDITIONING SYSTEM

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.

  1. I101550E01
    Remove the caps from the service valves on the refrigerant line.

  1. Connect the Freon collection/recycling device to discharge the refrigerant gas remaining in the refrigeration system.

    NOTICE:
    Use the Freon collection/recycling device in accordance with the manufacturer's instruction manual.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE FRONT SPOILER COVER LH (w/ Front Spoiler)

  1. B119950
    Remove the 5 screws and the front spoiler cover.


4. REMOVE FRONT SPOILER COVER RH (w/ Front Spoiler)

  1. B119934
    Remove the 4 screws and the front spoiler cover.


5. REMOVE FRONT BUMPER COVER

  1. B114359E01
    Apply protective tape as shown in the illustration.

  1. B119953
    w/ Front Spoiler:

    1. Remove the 3 screws.

    2. Remove the 2 screw grommets.

    3. Remove the 7 clips.

  1. B114360
    w/o Front Spoiler:

    1. Remove the 8 screws.

    2. Remove the 2 screw grommets.

    3. Remove the 7 clips.

  1. B114361E01
    w/ Fog Light:

    1. Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper cover.

    2. Disconnect the 2 fog light connectors.

  1. B114365E01
    w/o Fog Light:

    1. Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper cover.

  1. B119954
    w/ Front Spoiler:

    1. Remove the 2 clips and the 4 screw grommets.

  1. B114366
    w/o Front Spoiler:

    1. Remove the 2 clips and the screw grommet.


6. REMOVE RADIATOR SUPPORT ABSORBER UPPER

A104886E01
  1. Disengage the 6 claws and remove the radiator support absorber upper.


7. REMOVE NO. 1 COOLER COVER

A109229
  1. Remove the 2 clips and cooler cover No. 1.


8. SEPARATE HOOD LOCK ASSEMBLY

A104889
  1. Separate the hood lock control cable assembly from the 2 clamps.

  1. A104888
    Remove the 3 bolts and remove the hood lock assembly.


9. SEPARATE RADIATOR RESERVE TANK ASSEMBLY

10. REMOVE RADIATOR SUPPORT SUB-ASSEMBLY UPPER

A104890
  1. Separate the horn assembly connector.

  1. Remove the 4 bolts and remove the radiator support sub-assembly upper.


11. REMOVE RADIATOR SUPPORT EXTENSION RH (1ND-TV)

  1. I102276
    Disengage the 2 claws and remove the radiator support extension RH.


12. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

I102274E01
  1. Remove the bolt and disconnect the discharge hose from the cooler condenser.

  1. Remove the O-ring from the discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.


13. DISCONNECT LIQUID TUBE SUB-ASSEMBLY A

  1. I102275E01
    Remove the bolt and disconnect the liquid tube from the cooler condenser.

  1. Remove the O-ring from the liquid tube.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.


14. REMOVE CONDENSER

I102271
  1. Disengage the 2 claws and remove the condenser from the vehicle.

    NOTICE:
    Do not damage the condenser or radiator when removing the condenser.

← ON-VEHICLE INSPECTION (from Nov 2005)DISASSEMBLY (from Nov 2005) →