2005-2008 Yaris · Service Manual ENGINE

B2278 Engine Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

This DTC is output when 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.
DTC No.
DTC Detection Condition
Trouble Area
B2278
Communication is abnormal between main body ECU and engine switch or engine switch is defective
  1. Main body ECU
  2. Engine switch
  3. Wire harness

WIRING DIAGRAM

B082265E03

INSPECTION PROCEDURE


1. READ VALUE OF INTELLIGENT TESTER (START SWITCH 1 AND 2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Main Body ECU / Data List / St SW1 and St SW2.

  1. Read the value displayed on the tester.

    Main Body ECU:
    Item
    Measurement Item/Display (Range)
    Normal Condition
    Diagnostic Note
    St SW1
    Start Switch 1 / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    St SW 2
    Start Switch 2 / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -

    OK:
    ON appears on the screen.



NG
Go to step 3
OK


2. CHECK SWITCH CONDITION (ENGINE SWITCH)
  1. Ensure the electrical key is inside the cabin.

  1. Check that the power source mode changes as shown below each time the engine switch is.

OK:
off → on (ACC) → on (IG) → off



NG
GO TO POWER SOURCE MODE DOES NOT CHANGE
OK

SYSTEM IS OK

3. INSPECT ENGINE SWITCH
A109259E18
  1. Remove the engine switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher

  1. Reinstall the engine switch.



NG
REPLACE ENGINE SWITCH
OK


4. CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)

  1. A122232E04
    Disconnect the D55 engine switch connector.

  1. Disconnect the D65 main body ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D55-7 (SS1) - D65-10 (SSW1)
    Below 1 Ω
    D55-2 (SS2) - D65-9 (SSW2)
    Below 1 Ω
    D55-5 (GND) - Body ground
    Below 1 Ω
    D55-7 (SS1) or D65-10 (SSW1) - Body ground
    10 kΩ or higher
    D55-2 (SS2) or D65-9 (SSW2) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the engine switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2277 Detecting Vehicle Submersion (from Nov 2006)B2282 Vehicle Speed Signal Malfunction (+ B2283) (from Nov 2006) →