2005-2008 Yaris · Service Manual ENGINE

Engine Switch Indicator Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

Engine start conditions or system malfunctions can be checked by observing the status of the ignition switch indicator light.
Ignition switch indicator light condition 
Power Source Mode/Condition
Indicator Light Condition
Clutch pedal released (M/T)
Brake pedal released (except M/T)
Clutch pedal depressed (M/T)
Brake pedal depressed (except M/T)
Off
OFF
Illuminates (Green)
On (ACC, IG)
Illuminates (Amber)
Illuminates (Green)
Engine running
OFF
OFF
Steering lock not unlocked
Flashes (Green) for 15 seconds
Flashes (Green) for 15 seconds
System malfunction
Flashes (Amber) for 15 seconds
Flashes (Amber) for 15 seconds
Clutch switch malfunction (M/T)
Flashes (Green) for 15 seconds
Flashes (Green) for 15 seconds

WIRING DIAGRAM

A122428E01

INSPECTION PROCEDURE


1. INSPECT IGNITION SWITCH ASSEMBLY
A109259E04
  1. Remove the ignition switch.

  1. Apply the battery voltage between the terminals of the switch, and check the illumination condition of the ignition switch indicator light.

    NOTICE:
    1. If the positive (+) lead and the negative (-) lead are incorrectly connected, the ignition switch indicator light does not illuminate.
    2. If the voltage is too low, the indicator light does not illuminate.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 11 (SWIL)
    Battery negative (-) → Terminal 4 (COM) or 5 (GND)
    Illuminates
    Battery positive (+) → Terminal 12 (INDS)
    Battery negative (-) → Terminal 4 (COM) or 5 (GND)
    Illuminates
    Battery positive (+) → Terminal 13 (INDW)
    Battery negative (-) → Terminal 4 (COM) or 5 (GND)
    Illuminates

  1. Reinstall the ignition switch.



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - MAIN BODY ECU AND BODY GROUND)
A122429E02
  1. Disconnect the D55 ignition switch connector.

  1. Disconnect the D65 and D66 main body ECU connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D55-11 (SWIL) - D65-8 (SWIL)
    Below 1 Ω
    D55-12 (INDS) - D66-1 (INDS)
    Below 1 Ω
    D55-13 (INDW) - D66-8 (INDW)
    Below 1 Ω
    D55-5 (GND) - Body ground
    Below 1 Ω
    D55-4 (COM) - Body ground
    Below 1 Ω
    D55-11 (SWIL) or D65-8 (SWIL) - Body ground
    10 kΩ or higher
    D55-12 (INDS) or D66-1 (INDS) - Body ground
    10 kΩ or higher
    D55-13 (INDW) or D66-8 (INDW) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connectors.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Engine does not Start (from Nov 2005)COMPONENTS (from Nov 2005) →