Key Reminder Buzzer does not Sound
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the main body ECU sends a key switch signal and driver side courtesy switch signal to the combination meter.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Since the key reminder warning system has functions that use CAN communication, firstly confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with How to Proceed with Troubleshooting. Then, conduct the following troubleshooting procedure.
| 1. READ VALUE USING INTELLIGENT TESTER (KEY UNLOCK WARNING SW) |
Check the DATA LIST to ensure proper operation of the door unlock warning switch.
- Main Body ECU:
Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
Key Unlock Warning SW
Unlock warning switch signal / ON or OFF
ON: Key is in ignition key cylinder
OFF: No key is in ignition key cylinder
-
- OK:
- The display is as specified in the normal condition column.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (D DOOR COURTESY SW) |
Check the DATA LIST to ensure proper operation of the front door courtesy light switch.
- Main Body ECU:
Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
D Door Courtesy SW
Driver side door courtesy switch signal / ON or OFF
ON: Driver side door is open
OFF: Driver side door is closed
-
- OK:
- The display is as specified in the normal condition column.
|
|
||||
| OK | |
| 3. CHECK COMBINATION METER ASSEMBLY (WARNING BUZZER) |
Temporarily replace the combination meter assembly with a new or normally functioning one.
Check the key reminder warning system function. (Click here)
- OK:
- The key reminder warning system functions properly.
|
|
||||
| OK | ||
| ||
| 4. INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
Remove the unlock warning switch assembly.

Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Not pushed
10 kΩor higher
1 - 2
Pushed
Below 1 Ω
Reinstall the unlock warning switch assembly.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU) |
Disconnect the D19 unlock warning switch connector.

Disconnect the 4D main body ECU connector.
Measure the resistance between the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
D19-1 - 4D-7 (KSW)
Below 1 Ω
D19-1 or 4D-7 (KSW) - Body ground
10 kΩor higher
D19-2 - Body ground
Below 1 Ω
Reconnect the unlock warning switch and the main body ECU connectors.
|
|
||||
| OK | ||
| ||
| 6. INSPECT FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE) |
Remove the courtesy light switch.

Measure the resistance of the switch.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - Body ground
Not pushed (ON)
Below 1 Ω
1 - Body ground
Pushed (OFF)
10 kΩor higher
Reinstall the courtesy light switch.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH - MAIN BODY ECU) |
LHD:

Disconnect the J2 door courtesy switch connector.
Disconnect the 4A main body ECU connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
J2-1 - 4A-21 (DCTY)
Below 1 Ω
J2-1 or 4A-21 (DCTY) - Body ground
10 kΩor higher
Reconnect the courtesy switch and main body ECU connectors.
RHD:
Disconnect the J1 switch connector.
Disconnect the 4A main body ECU connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
J1-1 - 4A-21 (DCTY)
Below 1 Ω
J1-1 or 4A-21 (DCTY) - Body ground
10 kΩor higher
Reconnect the courtesy switch and main body ECU connectors.
|
|
||||
| OK | ||
| ||
