2005-2008 Yaris · Service Manual BODY

TERMINALS OF ECU

System information · Vehicles built from Aug 2005


CHECK POWER WINDOW REGULATOR MASTER SWITCH (W/ REAR POWER WINDOW)
B112771E02
  1. Disconnect the G1 or F7 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: w/ rear power window (LHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (G1-6) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (G1-6) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    E (G1-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    Standard: w/ rear power window (RHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (F7-6) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (F7-6) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    E (F7-9) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the G1 or F7 switch connector.

  4. Measure the voltage.

    Standard voltage: w/ rear power window (LHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (G1-3) - E (G1-1)
    R- W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    D (G1-4) - E (G1-1)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (G1-4) - E (G1-1)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    U (G1-16) - E (G1-1)
    W - W-B
    Power window motor UP output
    Ignition switch ON, passenger side power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (G1-15) - E (G1-1)
    P - W-B
    Power window motor DOWN output
    Ignition switch ON, passenger side power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    U (G1-12)* - E (G1-1)
    Y - W-B
    Power window motor UP output
    Ignition switch ON, rear LH side power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (G1-13)* - E (G1-1)
    B - W-B
    Power window motor DOWN output
    Ignition switch ON, rear LH side power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    U (G1-10)* - E (G1-1)
    R - W-B
    Power window motor UP output
    Ignition switch ON, rear RH side power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (G1-18)* - E (G1-1)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, rear RH side power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    Standard voltage: w/ rear power window (RHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (F7-4) - E (F7-9)
    R- W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    D (F7-3) - E (F7-9)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (F7-3) - E (F7-9)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    U (F7-12) - E (F7-9)
    W - W-B
    Power window motor UP output
    Ignition switch ON, passenger side power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (F7-13) - E (F7-9)
    P - W-B
    Power window motor DOWN output
    Ignition switch ON, passenger side power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    U (F7-18)* - E (F7-9)
    Y - W-B
    Power window motor UP output
    Ignition switch ON, rear LH side power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (F7-10)* - E (F7-9)
    B - W-B
    Power window motor DOWN output
    Ignition switch ON, rear LH side power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    U (F7-16)* - E (F7-9)
    R - W-B
    Power window motor UP output
    Ignition switch ON, rear RH side power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (F7-15)* - E (F7-9)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, rear RH side power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    *: With rear power window
    If the result is not as specified, the master switch may have a malfunction.

  5. Check the AUTO light illumination.

    1. After turning the ignition switch ON, check that the AUTO light illuminates (green).


CHECK POWER WINDOW REGULATOR MASTER SWITCH (W/O REAR POWER WINDOW)
B112771E02
  1. Disconnect the G1 or F7 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: w/o rear power window (LHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (G1-15) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (G1-15) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    E (G1-7) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    Standard: w/o rear power window (RHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (F7-15) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (F7-15) - Body ground
    GR - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    E (F7-7) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the G1 or F7 switch connector.

  4. Measure the voltage.

    Standard voltage: w/o rear power window (LHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (G1-10) - E (G1-7)
    R - W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    D (G1-12) - E (G1-7)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (G1-12) - E (G1-7)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    U (G1-16) - E (G1-7)
    W - W-B
    Power window motor UP output
    Ignition switch ON, passenger side power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (G1-18) - E (G1-7)
    P - W-B
    Power window motor DOWN output
    Ignition switch ON, passenger side power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    Standard voltage: w/o rear power window (RHD) 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U (F7-18) - E (F7-7)
    R - W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    D (F7-16) - E (F7-7)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    D (F7-16) - E (F7-7)
    G - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V
    U (F7-12) - E (F7-7)
    W - W-B
    Power window motor UP output
    Ignition switch ON, passenger side power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (F7-10) - E (F7-7)
    P - W-B
    Power window motor DOWN output
    Ignition switch ON, passenger side power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    If the result is not as specified, the master switch may have a malfunction.

  5. Check the AUTO light illumination.

    1. After turning the ignition switch ON, check that the AUTO light illuminates (green).


CHECK POWER WINDOW SWITCH (PASSENGER SIDE)
B121518E01
  1. Disconnect the F1 or G7 switch connector.

  2. Measure the voltage of the wire harness side connector.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (3) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (3) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    D (1) - Body ground
    G - Body ground
    Power window motor DOWN output
    Ignition switch ON, power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    SD (2) - Body ground
    P - Body ground
    Power window motor DOWN input (Remote)
    Ignition switch ON, power window master switch OFF → DOWN (Remote)
    Below 1 V → 10 to 14 V
    U (4) - Body ground
    R - Body ground
    Power window motor UP output
    Ignition switch ON, power window switch OFF → UP
    Below 1 V → 10 to 14 V
    SU (5) - Body ground
    W - Body ground
    Power window motor UP input (Remote)
    Ignition switch ON, power window master switch OFF → UP (Remote)
    Below 1 V → 10 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK POWER WINDOW SWITCH (REAR DOOR SIDE)
B116303E01
  1. Disconnect the I1 and H1 switch connectors.

  2. Measure the voltage of the wire harness side connectors.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (3) - Body ground
    SB - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    B (3) - Body ground
    SB - Body ground
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    U (4) - Body ground
    Y - Body ground
    Power window motor UP output
    Ignition switch ON, power window switch OFF → UP
    Below 1 V → 10 to 14 V
    D (2) - Body ground
    B - Body ground
    Power window motor DOWN output
    Ignition switch ON, power window switch OFF → DOWN
    Below 1 V → 10 to 14 V
    SU (5) - Body ground
    R - Body ground
    Power window motor UP intput (Remote)
    Ignition switch ON, power window master switch OFF → UP (Remote)
    Below 1 V → 10 to 14 V
    SD (1) - Body ground
    G - Body ground
    Power window motor DOWN input (Remote)
    Ignition switch ON, power window master switch OFF → DOWN (Remote)
    Below 1 V → 10 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

← PROBLEM SYMPTOMS TABLE (from Aug 2005)ON-VEHICLE INSPECTION (from Aug 2005) →