2005-2008 Yaris · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL TRANSAXLE CASE STRAIGHT PIN

  1. G021125E01
    Install the transaxle case straight pin.

    Standard depth:
    10.5 to 11.5 mm (0.4134 to 0.4528 in.)


2. INSTALL OUTPUT SHAFT COVER

  1. G021158E04
    Install the output shaft cover as shown in the illustration.


3. INSTALL OUTPUT SHAFT FRONT BEARING

  1. G021159E02
    Using SST and a press, press in the output shaft front bearing (outer race).
    SST
    09950-60010   (09951-00510)
    09950-70010   (09951-07150)


4. INSTALL FR DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

  1. G021160E02
    Using SST and a press, press in the front differential case front tapered roller bearing (outer race).
    SST
    09350-32014   (09351-32111, 09351-32130)


5. INSTALL FR DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

  1. G021161E02
    Install the shim onto the manual transmission case.

    HINT:
    When re-using the output shaft rear tapered roller bearing, first install a shim of the same thickness as before. If installing a new output shaft rear tapered roller bearing, first select and install a shim which is thinner than the original.

  1. Using SST and a press, press in the FR differential case rear tapered roller bearing (outer race).

    SST
    09950-60010   (09951-00620)
    09950-70010   (09951-07100)


6. INSPECT DIFFERENTIAL SIDE BEARING PRELOAD

  1. G021163E02
    Coat the differential case assembly with gear oil, and install it onto the front transaxle case.

  1. D005714E01
    Install the manual transmission case with the 13 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    HINT:
    Manual transmission case side: 8 bolts
    Front transaxle case side: 5 bolts

  1. G021162E02
    Using SST and a torque wrench, turn the differential case assembly right and left 2 or 3 times to allow the bearings to settle.
    SST
    09564-32011  

  1. Using SST and a torque wrench, measure the preload.

    SST
    09564-32011  

    Preload (at starting):
    New bearing:
    0.78 to 1.57 N*m (7.95 to 16.00 kgf*cm, 6.9 to 13.89 in.*lbf)
    Used bearing:
    0.49 to 0.98 N*m (5.00 to 9.99 kgf*cm, 4.3 to 8.67 in.*lbf)

  1. Select another shim.

    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    AA
    2.10 (0.0827)
    HH
    2.45 (0.0965)
    QQ
    2.80 (0.1102)
    BB
    2.15 (0.0847)
    JJ
    2.50 (0.0984)
    RR
    2.85 (0.1122)
    CC
    2.20 (0.0866)
    KK
    2.55 (0.1004)
    SS
    2.90 (0.1142)
    DD
    2.25 (0.0886)
    LL
    2.60 (0.1024)
    TT
    2.95 (0.1161)
    EE
    2.30 (0.0906)
    MM
    2.65 (0.1043)
    UU
    3.00 (0.1181)
    FF
    2.35 (0.0925)
    NN
    2.70 (0.1063)
    -
    -
    GG
    2.40 (0.0945)
    PP
    2.75 (0.1083)
    -
    -

  1. Remove the 13 bolts and the manual transmission case from the front transaxle case.

  1. Remove the differential case assembly from the front transaxle case.


7. INSTALL OUTPUT SHAFT REAR BEARING

  1. G021164E01
    Install the output shaft rear bearing shim onto the manual transmission case.

    HINT:
    When re-using the output shaft rear tapered roller bearing, first install a shim of the same thickness as before. If installing a new output shaft rear tapered roller bearing, first select and install a shim which is thinner than the original.

  1. G021165E02
    Using SST and a press, press in the output shaft rear bearing (outer race).
    SST
    09950-60010   (09951-00570)
    09950-70010   (09951-07200)


8. ADJUST OUTPUT SHAFT BEARING PRELOAD

  1. G021166E01
    Install the output shaft assembly and the differential case assembly onto the front transaxle case.

  1. D005714
    Install the manual transmission case onto the front transaxle case with the 13 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. G021162E03
    Using SST and a torque wrench, turn the output shaft assembly and differential case assembly right and left 2 or 3 times to allow the bearings to settle.
    SST
    09564-32011  

  1. Using SST and a torque wrench, measure the preload.

    SST
    09564-32011  

    Preload (at starting):
    New bearing:
    3.46 to 6.91 N*m (35.3 to 70.5 kgf*cm, 30.6 to 61.2 in.*lbf) for 1KR-FE
    3.18 to 6.35 N*m (32.4 to 64.7 kgf*cm, 28.1 to 56.2 in.*lbf) for 2SZ-FE
    Used bearing:
    2.16 to 4.32 N*m (22.0 to 44.1 kgf*cm, 19.1 to 38.2 in.*lbf) for 1KR-FE
    1.98 to 3.97 N*m (20.2 to 40.5 kgf*cm, 17.5 to 35.1 in.*lbf) for 2SZ-FE

  1. Select another output shaft rear bearing shim.

    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    A
    1.55 (0.0610)
    J
    1.95 (0.0768)
    B
    1.60 (0.0630)
    K
    2.00 (0.0787)
    C
    1.65 (0.0650)
    L
    2.05 (0.0807)
    D
    1.70 (0.0669)
    M
    2.10 (0.0827)
    E
    1.75 (0.0689)
    N
    2.15 (0.0846)
    F
    1.80 (0.0709)
    P
    2.20 (0.0866)
    G
    1.85 (0.0728)
    Q
    2.25 (0.0886)
    H
    1.90 (0.0748)


  1. D005714E01
    Remove the 13 bolts and the manual transmission case from the front transaxle case.

  1. Remove the output shaft assembly from the front transaxle case.

  1. Remove the differential case assembly from the front transaxle case.


9. INSTALL INPUT SHAFT REAR BEARING SHIM

  1. D006020E02
    Using vernier calipers, accurately measure dimensions A and B.

  1. Select an input shaft rear bearing shim that brings the value within the specifications.

    Shim thickness:
    Shim thickness (B - A) should be more than 0 mm (0 in.) and less than 0.1 mm (0.0039 in.)

    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    F
    1.80 (0.0709)
    N
    2.15 (0.0846)
    G
    1.85 (0.0728)
    P
    2.20 (0.0866)
    H
    1.90 (0.0748)
    Q
    2.25 (0.0886)
    J
    1.95 (0.0768)
    R
    2.30 (0.0906)
    K
    2.00 (0.0787)
    S
    2.35 (0.0925)
    L
    2.05 (0.0807)
    T
    2.40 (0.0945)
    M
    2.10 (0.0827)
    -
    -

  1. Install the input shaft rear bearing shim.


10. INSTALL TRANSMISSION CASE OIL SEAL

  1. G021167E02
    Using SST and a hammer, install a new transmission case oil seal into the manual transmission case.
    SST
    09950-60010   (09951-00370)
    09950-70010   (09951-07150)

    Drive in depth:
    2.1 to 3.1 mm (0.083 to 0.122 in.)

  1. Coat the tip of the transmission oil seal with MP grease.


11. INSTALL TRANSAXLE CASE OIL SEAL

  1. G021176E02
    Using SST and a hammer, install the transaxle case oil seal to the front transaxle case.
    SST
    09316-60011   (09316-00011)

    Drive in depth:
    1.7 to 2.7 mm (0.067 to 0.106 in.)

  1. Coat the tip of the transmission case oil seal with MP grease.


12. INSTALL FRONT TRANSAXLE CASE OIL SEAL

  1. C081790E02
    Using SST and a hammer, install the front transaxle case oil seal into the front transaxle case.
    SST
    09710-20011   (09710-06071)
    09950-70010   (09951-07150)

    Drive in depth:
    14.4 to 15.4 mm (0.567 to 0.606 in.)

  1. Coat the tip of the front transaxle case oil seal with MP grease.


13. INSTALL TRANSMISSION MAGNET

  1. G021178E01
    Clean the transmission magnet and then install it onto the front transaxle case.


14. INSTALL OIL RECEIVER PIPE NO. 2

  1. D005736E02
    Install oil receiver pipe No. 2 onto the manual transmission case.

    NOTICE:
    Do not damage oil receiver pipe No. 2.


15. INSTALL FRONT DIFFERENTIAL CASE

  1. G021163E01
    Coat the differential case tapered roller bearings with gear oil, and install them onto the front transaxle case.


16. INSTALL OUTPUT SHAFT

  1. G021166E01
    Install the output shaft assembly onto the front transaxle case.


17. INSTALL INPUT SHAFT

  1. G021179E01
    Coat the sliding and rotating surfaces of the input and output shafts assembly with gear oil, and install them onto the front transaxle case.


18. INSTALL GEAR SHIFT FORK SHAFT NO.2

  1. C112782
    Install gear shift fork No. 2 onto gear shift fork shaft No. 2.

  1. Using a screwdriver and hammer, install a new snap ring onto gear shift fork shaft No. 2.

  1. C112783
    Install the reverse shift fork onto gear shift fork shaft No. 2.

  1. Using a screwdriver and hammer, install a new snap ring onto gear shift fork shaft No. 2.

  1. C112779
    Shift hub sleeve No. 2 into the 3rd gear, as shown.

  1. C112780
    Install gear shift fork shaft No. 2 with the 2 snap rings.

  1. Install gear shift fork No.2 and reverse shift fork onto the transaxle case.

  1. Set gear shift fork No. 2 onto hub sleeve No. 2.

  1. Install the set bolt onto gear shift fork No. 2.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }

  1. C112778E01
    Using a magnetic finger, install the straight pin into the reverse shift fork.

    NOTICE:
    Insert the straight pin along the groove on gear shift fork shaft No. 2, as shown in the illustration.


19. INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

  1. C112777
    Install the reverse shift arm bracket onto the transaxle case with the 2 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Fit the edge of the reverse shift fork into the hole in the reverse shift arm bracket.


20. INSTALL REVERSE IDLER GEAR SHAFT

  1. C112776
    Coat the reverse idler gear shaft with gear oil, and install it onto the transmission case.

    NOTICE:
    Set the top of the reverse shift arm bracket into the groove on the reverse idler gear, as shown in the illustration.

  1. C112784E01
    Align the mark on the reverse idler gear shaft with the bolt hole, as shown in the illustration.


21. INSTALL GEAR SHIFT FORK SHAFT NO.3

  1. C112785
    Install gear shift fork No. 3, the compression spring and gear shift head No. 3 onto gear shift fork shaft No. 3.

  1. Install gear shift fork shaft No. 3 onto the transaxle case together with gear shift fork No. 3, the compression spring and shift head No. 3.

  1. Set gear shift fork No. 3 onto hub sleeve No. 3.

  1. Using a screwdriver and hammer, tap 2 new snap rings onto gear shift fork shaft No. 3.

  1. C112773
    Using a magnetic finger, install the straight pin onto gear shift fork No. 3.


22. INSTALL GEAR SHIFT FORK SHAFT NO.1

  1. C112786
    Using a screwdriver and hammer, install a new snap ring onto gear shift fork shaft No. 1.

  1. C112787
    Set gear shift fork No. 1 onto the reverse gear.

  1. Set gear shift head No. 1 onto gear shift fork No. 1.

  1. Install gear shift fork shaft No. 1 onto the transaxle case with the snap ring.

    NOTICE:
    Insert the straight pin along the groove on gear shift fork shaft No. 1, as shown in the illustration.

  1. Install the set bolt onto gear shift fork No. 1.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


23. INSTALL SHIFT HEAD SET SLOTTED SPRING PIN

  1. C112770E01
    Using a pin punch and hammer, tap the 2 slotted spring pins into the No. 1 and No. 3 gear shift heads.

    Drive in depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)


24. INSTALL INPUT SHAFT REAR BEARING SHIM

  1. C112769
    Install the input shaft rear bearing shim onto the transmission case.

    HINT:
    Install the previously selected shim.


25. INSTALL MANUAL TRANSMISSION CASE

  1. C112788E01
    Apply FIPG to the transmission case, as shown in the illustration.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

    NOTICE:
    Assemble the parts within 10 minutes of application.

  1. C112768
    Coat the 13 bolts with sealant.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Install the transmission case onto the transaxle case with the 13 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


26. INSTALL REVERSE IDLER GEAR SHAFT BOLT

  1. C112767
    Apply sealant to the reverse idler gear shaft lock bolt threads.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Install the reverse idler gear shaft lock bolt with a new gasket.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


27. INSTALL TRANSMISSION REVOLUTION SENSOR

  1. C112766
    Install a new O-ring onto the transmission revolution sensor.

  1. Install the transmission revolution sensor with the bolt.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Install the transmission case protector with the bolt.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }


28. INSTALL SHIFT AND SELECT ACTUATOR ASSEMBLY

  1. C112789E01
    Apply FIPG to the transmission case as shown.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

  1. Apply sealant to the actuator set bolt threads.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. C136388
    Install the shift and select actuator with the 6 bolts and wire harness clamp.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


29. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C114061E01
    Using SST, install the park/neutral position switch with a new gasket onto the transaxle case.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }

    SST
    09817-16011  


30. INSTALL LOCK BALL ASSEMBLY NO.1

  1. C112762
    Apply sealant to the lock ball assembly threads.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Using an 18 mm socket wrench, install the lock ball assembly onto the transmission case.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


31. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

  1. C112765E01
    Using SST, install the back-up light switch with a new gasket onto the transaxle case.
    SST
    09817-16011  

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }


32. INSTALL CLUTCH RELEASE FORK LEVER SHAFT OIL SEAL

33. INSTALL CLUTCH RELEASE FORK

34. INSTALL SHIFT STROKE SENSOR
← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →