2005-2008 Yaris · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jan 2006

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.


3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106371
    Release the 2 knobs and remove the deck board.


4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Remove the spare wheel cover.


5. REMOVE DECK FLOOR BOX RH (w/ Deck Board)

  1. B106372
    Release the 2 knobs and remove the deck floor box.


6. REMOVE DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B138392
    Remove the rear floor carpet.


8. REMOVE NO. 1 REAR SEAT LEG COVER

  1. B124298
    Disengage the 4 claws and remove the No. 1 rear seat leg cover.


9. REMOVE NO. 2 REAR SEAT LEG COVER

  1. B124330
    Disengage the 6 claws and remove the No. 2 rear seat leg cover.


10. REMOVE REAR SEAT ASSEMBLY RH

  1. B124299
    Using "Torx" socket wrench E10, remove the 2 bolts and pull up the rear seat cushion.

  1. B124300
    Using "Torx" socket wrench E10, remove the 2 bolts and rear seat.


11. REMOVE REAR SEAT ASSEMBLY LH

  1. B124331
    Using "Torx" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.

  1. B124315
    Using "Torx" socket wrench E10, remove the 4 bolts and the rear seat.


12. REMOVE FRONT DOOR SCUFF PLATE RH

  1. B114494
    Disengage the 8 claws and remove the front door scuff plate.


13. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


14. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH

  1. B114571
    Disengage the 4 claws and remove the instrument panel under cover.


15. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH

  1. B114572
    Remove the 2 screws.

  1. Disengage the 3 claws and remove the instrument panel under cover.


16. REMOVE COWL SIDE TRIM BOARD RH

  1. B114285
    Disengage the claw and the stud bolt and remove the cowl side trim board.


17. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B138507
    Remove the front door opening trim weatherstrip.


19. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


20. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH

  1. B114759
    Remove the 2 bolts and the front seat outer belt bar.


21. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


22. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

  1. B114498
    Remove the belt of the rear seat outer belt from the rear seat shoulder belt hanger.

  1. B114499
    Disengage the 8 clips, the retainer and the 10 claws and remove the front quarter trim panel.


23. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


24. REMOVE REAR DECK TRIM COVER

  1. B114283
    for Grand Tire:

    1. Using a clip remover, remove the 2 clips.

    2. Disengage the 8 claws and remove the rear deck trim cover.

  1. B117692
    for Temper Spare Tire:

    1. Using a clip remover, remove the 2 clips.

    2. Disengage the 8 claws and remove the rear deck trim cover.


25. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH

  1. B114500
    Remove the bolt.

  1. Disengage the clip and remove the anchor plate.


26. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


27. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

  1. B114501
    Remove the 3 screws.

  1. Disengage the 3 clips and the 3 claws and remove the deck side trim panel.


28. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

  1. B114502
    Remove the 3 screws.

  1. Disengage the 3 clips and the 3 claws.

  1. Disconnect the deck side room light connector and remove the deck side trim panel.


29. REMOVE SEAT BELT ANCHOR COVER CAP

B114478

HINT:
Use the same procedure for both sides.

  1. Disengage the 3 claws and remove the seat belt anchor cover cap.


30. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH

  1. B114479
    Remove the bolt and the through anchor.


31. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


32. REMOVE CENTER PILLAR UPPER GARNISH RH

  1. B114503
    Disengage the 2 clips and remove the center pillar garnish.


33. REMOVE CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.


34. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B114459
    Remove the 2 tongue plates.

  1. B114460E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the slip joint cover.

  1. B114461
    Remove the bolt and the through anchor.

  1. B114462E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the center belt guide.


35. REMOVE ROOF SIDE INNER GARNISH RH

  1. B114504E01
    w/ Curtain Shield Airbag:

    NOTICE:
    Replace the special clip with a new one when the roof side inner garnish is removed.


    1. Disengage the 4 clips and the claw.

    2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.

  1. B114505
    w/o Curtain Shield Airbag:

    1. Disengage the 4 clips and the claw.

    2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.


36. REMOVE ROOF SIDE INNER GARNISH LH

  1. B114506E01
    w/ Curtain Shield Airbag:

    NOTICE:
    Replace the special clip with a new one when the roof side inner garnish is removed.


    1. Disengage the 4 clips and claw.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.

  1. B114507
    w/o Curtain Shield Airbag:

    1. Disengage the 4 clips and claw.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.


37. REMOVE REAR ROOF SIDE RAIL GARNISH RH

  1. B114508
    Disengage the 4 clips and remove the rear roof side rail garnish.


38. REMOVE REAR ROOF SIDE RAIL GARNISH LH

HINT:
Use the same procedure as for the RH side.


39. REMOVE SEAT BELT ANCHOR COVER

40. REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)

B114299E01

HINT:
The number of the roof headlining service hole covers varies with the specifications.

  1. Using a clip remover with its tip wrapped in protective tape, remove the roof headlining service hole cover.


41. REMOVE COAT HOOK (w/ Coat Hook)

  1. B124367E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the cover.

  1. B124368E01
    Using a clip remover with its tip wrapped in protective tape, disengage the 2 claws and remove the coat hook.


42. REMOVE ASSIST GRIP COVER

B114301E01

HINT:
The number of the assist grip covers varies with the specifications.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the 4 assist grip covers.


43. REMOVE ASSIST GRIP SUB-ASSEMBLY

B114302

HINT:
The fitting number of the assist grips varies with the specifications.

  1. Disengage the 2 springs and remove the assist grip.


44. REMOVE VISOR ASSEMBLY RH

  1. B114303E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.

  1. B114304
    Remove the visor shaft from the visor holder.

  1. Disengage the 2 springs and remove the visor.


45. REMOVE VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


46. REMOVE VISOR HOLDER RH

  1. B114305E01
    Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.

    HINT:
    The claw may be damaged during removal. However, it is reusable because this does not effect its function.


47. REMOVE VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.


48. REMOVE ROOM LIGHT ASSEMBLY

  1. B114306E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.

  1. B124365E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 covers.

  1. B114307E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.

  1. B114308E01
    Remove the roof wire from the claw of the room light.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.


49. REMOVE MAP LIGHT ASSEMBLY

  1. B114309E01
    Using a roof moulding remover, disengage the 4 claws and remove the map light.

  1. B114310
    Disconnect the map light connector.


50. REMOVE FRONT PILLAR GARNISH RH

  1. B117693E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B117694
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B114312
    Disconnect the connector.

  1. Using a clip remover, remove the 3 antenna cord clamps.

  1. B127674
    Disconnect the speaker connector.

  1. B127670E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.

  1. B114313E01
    w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


51. REMOVE FRONT PILLAR GARNISH LH

  1. B117695E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B117696
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B114316
    Using a clip remover, remove the 4 wiring harness clamps.

  1. B127673
    Disconnect the speaker connector.

  1. B127669E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.

  1. B114317E01
    w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


52. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.

  1. E107742E01
    Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.


53. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.

  1. E107744E01
    Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.


54. REMOVE INSTRUMENT CLUSTER FINISH PANEL

B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.

  1. B132364
    Disengage the 2 claws and 5 clips.

  1. B132365E01
    After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.


55. REMOVE COMBINATION METER ASSEMBLY

E107730
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.


56. REMOVE NO. 1 SWITCH HOLE BASE (for LHD)

B108201
  1. Disengage the 2 clips and 2 claws and remove the switch hole base.


57. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

B108202
  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.

  1. B105351
    Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.


58. REMOVE INSTRUMENT UPPER PANEL SUB-ASSEMBLY

B108181E02
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.

  1. Remove the 2 <C> bolts and 4 <B> screws.

    B105354E01

  1. Disconnect the connectors.

  1. Disengage the claw and 3 clips while lifting the rear instrument panel up.

  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.

    B105355E01


59. REMOVE INSTRUMENT PANEL BOX (for LHD)

B108188E01
  1. Open the instrument panel box.

  1. Pull the hinge side of the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.

  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.


60. REMOVE ROOF HEADLINING ASSEMBLY

  1. B114511
    for LHD:

    1. Using a screwdriver, remove the wiring harness clamp.

    2. Disconnect the connector.

  1. B114319
    for RHD:

    1. Using a screwdriver, remove the wiring harness clamp.

    2. B114320
      Remove the No. 1 roof wire from the claw of the junction block.

    3. Disconnect the connector.

  1. B114321
    Remove the antenna cord from the antenna cord clamp.

  1. Disconnect the 2 connectors.

  1. Using a clip remover, remove the 2 connectors.

  1. w/ Curtain Shield Airbag:

    1. Using a clip remover, remove the clip.

    2. Disengage the 4 hooks.

      B138509

  1. w/o Curtain Shield Airbag:

    1. Using a clip remover, remove the clip.

    2. Disengage the 2 claws and the 4 hooks.

      B138510

  1. B114515
    Remove the roof headlining from the back door.

← COMPONENTS (from Jan 2006)DISASSEMBLY (from Jan 2006) →