2005-2008 Yaris · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jan 2006

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE FRONT SEAT HEADREST ASSEMBLY

B138501E01

HINT:
Use the same procedure for both sides.

  1. Push in the lock button of the front seat headrest support and remove the front seat headrest.


3. REMOVE FRONT SEAT ASSEMBLY LH

  1. B138315E01
    w/ Front Seat Side Airbag:

    1. Slide the slider and disconnect the airbag connector.

  1. Disconnect the buckle switch connector.

  1. B138317
    Move the front seat to its most rearward position.

  1. Using "Torx" socket wrench E10, remove the 2 bolts from the front side.

  1. Move the front seat to its most forward position.

  1. Using "Torx" socket wrench E10, remove the 2 bolts from the rear side and the front seat.


4. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


5. REMOVE REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Remove the rear seat cushion cover pad sub-assembly (Click here).

  1. for Fixed Seat Type:

    1. Remove the rear seat cushion cover pad sub-assembly (Click here).


6. REMOVE REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)

  1. B134924
    Remove the rear seat outer belt from the rear seat shoulder belt guide.

  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. B134925
    Using a clip remover, remove the 2 clips and the rear seatback cover.

  1. B134926
    Remove the 2 bolts, the 2 hooks and the rear seatback.


7. REMOVE REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)

  1. B134943
    Remove the rear seat outer belt from the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Center Seat Belt:

    1. Remove the rear center seat outer belt from the rear center seat shoulder belt guide.

  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. B134944
    Using a clip remover, remove the 2 clips and the rear seatback cover.

  1. B134945
    Remove the 2 bolts, the 2 hooks and the rear seatback.


8. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B138450E01
    Remove the rear seat outer belt from the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Remove the rear center seat outer belt from the rear center seat shoulder belt guide.

  1. B134981
    Remove the 3 bolts.

  1. Disengage the 3 hooks and remove the rear seatback.


9. REMOVE LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)

B136269
  1. Remove the luggage compartment floor mat.


10. REMOVE SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)

B136270
  1. Remove the spare wheel cover.


11. REMOVE LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)

B136275
  1. Remove the luggage compartment trim inner pad.


12. REMOVE FRONT DOOR SCUFF PLATE RH

  1. B134764
    Disengage the 11 claws and remove the front door scuff plate.


13. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


14. REMOVE COWL SIDE TRIM BOARD RH

  1. B114285
    Disengage the claw and the stud bolt and remove the cowl side trim board.


15. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B134765
    Remove the front door opening trim weatherstrip.


17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


18. REMOVE REAR DOOR SCUFF PLATE RH

  1. B134771
    Disengage the 7 claws and remove the rear door scuff plate.


19. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


20. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B134772
    Remove the rear door opening trim weatherstrip.


21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


22. REMOVE REAR SEAT SIDE COVER RH

  1. B134776
    Disengage the 2 clips and the 4 claws and remove the rear seat side cover.


23. REMOVE REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.


24. REMOVE ROOF SIDE INNER GARNISH RH

  1. B134775E01
    w/ Curtain Shield Airbag:

    NOTICE:
    Replace the special clip with a new one when the roof side inner garnish is removed.


    1. Disengage the 4 clips and the claw and remove the roof side inner garnish.

  1. B134774
    w/o Curtain Shield Airbag:

    1. Disengage the 4 clips and the claw and remove the roof side inner garnish.


25. REMOVE ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.


26. REMOVE CENTER PILLAR LOWER GARNISH RH

  1. B134767
    Disengage the 3 claws and 2 clips and remove the center pillar lower garnish.


27. REMOVE CENTER PILLAR LOWER GARNISH LH

HINT:
Use the same procedure as for the RH side.


28. REMOVE SEAT BELT ANCHOR COVER CAP

B138431E01

HINT:
Use the same procedure for both sides.

  1. Pull portion A, shown in the illustration, toward you, remove the 2 claws on the lower side followed by the claw on the upper side. Then remove the seat belt anchor cover cap.


29. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH

  1. B114296
    Remove the bolt and the through anchor.


30. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


31. REMOVE CENTER PILLAR UPPER GARNISH RH

  1. B134768
    Disengage the 2 clips and 2 hooks and remove the center pillar upper garnish.


32. REMOVE CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.


33. REMOVE FRONT PILLAR GARNISH RH

  1. B134777E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B134779
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B134787
    Disconnect the antenna connector.

  1. Using a clip remover, remove the 3 clamps.

  1. B138437E01
    w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


34. REMOVE FRONT PILLAR GARNISH LH

  1. B134778E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B134780
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B134789
    Using a clip remover, remove the 4 clamps.

  1. B138438E01
    w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


35. REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

B132316
  1. Disengage the 2 claws and 2 clips and remove the instrument panel finish panel lower center.


36. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B132387
    Remove the shift lever knob.


37. REMOVE REAR CONSOLE BOX UPPER FRONT PANEL SUB-ASSEMBLY

  1. B132347
    Shift the shift lever into the N position.

  1. Disengage the 5 clips and the claw and remove the upper console panel.


38. REMOVE REAR CONSOLE BOX UPPER REAR PANEL SUB-ASSEMBLY

  1. B132348
    Disengage the 3 clips and 3 claws.

  1. Disconnect the connector and remove the console upper rear panel.


39. REMOVE REAR CONSOLE BOX CARPET

B132346
  1. Remove the console box carpet.


40. REMOVE REAR CONSOLE BOX ASSEMBLY

  1. B132349
    Disconnect the clamp.

  1. Remove the 2 bolts and 2 screws.

  1. Disengage the 4 claws and remove the rear console box.


41. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

B132318
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end RH.


42. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

B132317
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end LH.


43. REMOVE INSTRUMENT CLUSTER FINISH PANEL

E116832
  1. Disengage the 4 claws and 5 clips and remove the instrument cluster finish panel.


44. REMOVE COMBINATION METER ASSEMBLY

E116819
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.


45. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

B132319E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door.

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.

  1. B132320E01
    Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.


46. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

B132322E01
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.

  1. Remove the 2 <C> bolts and 2 <B> screws.

    B132323E01

  1. Disengage the 7 clips by lifting the rear side of the instrument panel up.

    B132324

  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws from the front side of the instrument panel and remove the instrument panel.


47. REMOVE INSTRUMENT PANEL BOX (for LHD)

B132334E01
  1. Open the instrument panel box.

  1. Pull the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.

  1. B132335E01
    Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.


48. REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)

B134784

HINT:
The number of the roof headlining service hole covers varies with the specifications.

  1. B114299E01
    Using a clip remover with its tip wrapped in protective tape, remove the 2 roof headlining service hole covers.


49. REMOVE ASSIST GRIP COVER

B134785

HINT:
The number of the assist grip covers varies with the specifications.

  1. B114301E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip cover.


50. REMOVE ASSIST GRIP SUB-ASSEMBLY

B134786

HINT:
The number of the assist grips varies with the specifications.

  1. B114302
    Disengage the 2 springs and remove the assist grip.


51. REMOVE VISOR ASSEMBLY RH

  1. B114303E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.

  1. B114304
    Remove the visor shaft from the visor holder.

  1. Disengage the 2 springs and remove the visor.


52. REMOVE VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


53. REMOVE VISOR HOLDER RH

  1. B114305E01
    Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.

    HINT:
    The claw may be damaged during removal. However, it is reusable because this does not effect its function.


54. REMOVE VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.


55. REMOVE ROOM LIGHT ASSEMBLY

  1. B114306E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.

  1. B138435E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.

    HINT:
    Use the same procedure for both sides.

  1. B114307E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.

  1. B138436E01
    Remove the roof wire from the claw of the room light.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and disconnect the room light switch base.


56. REMOVE MAP LIGHT ASSEMBLY

  1. B114309E01
    Using a moulding remover, disengage the 4 claws and remove the map light.

  1. B138432
    Disconnect the map light connector.


57. REMOVE ROOF HEADLINING ASSEMBLY

  1. B134790
    Using a clip remover, remove the 2 clamps.

  1. B134791
    for LHD:

    1. Disconnect the roof wire connector.

  1. B134792
    for RHD:

    1. Disconnect the roof wire connector.

    2. Remove the roof wire from the clamp.

  1. B134788
    Using a clip remover, remove the clamp.

  1. Disconnect the antenna connector.

  1. B134793
    w/ Curtain Shield Airbag:

    1. Using a clip remover, remove the 2 clips.

    2. Disengage the 4 hooks.

  1. B134794
    w/o Curtain Shield Airbag:

    1. Using a clip remover, remove the 2 clips.

    2. Disengage the 2 claws and 4 hooks.

  1. B134795
    Remove the roof headlining from the front door.

← COMPONENTS (from Jan 2006)INSTALLATION (from Jan 2006) →