REMOVAL
Removal / installation · Vehicles built from Aug 2005
- CAUTION:
- Always use "Torx" socket wrench E10 when removing the rear seat.
- HINT:
- The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.
| 1. REMOVE CABLE FROM NEGATIVE BATTERY TERMINAL (for LH Side) |
| 2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
Remove the 2 package tray trim suspenders.

Remove the 5 pieces of hook tape.
Disengage the 2 claws and remove the package tray trim.
| 3. REMOVE DECK BOARD SUB-ASSEMBLY |
Release the 2 knobs and remove the deck board.

| 4. REMOVE DECK FLOOR BOX RH |
Release the 2 knobs and remove the deck floor box.

| 5. REMOVE DECK FLOOR BOX LH |
- HINT:
- Use the same procedure as for the RH side.
| 6. REMOVE REAR SEAT CUSHION COVER PAD |
Hold the front edge of the rear seat cushion and lift it up, as shown in the illustration, to disengage the the 2 rear seat cushion lock hooks.

- NOTICE:
- Hold the area around the rear seat cushion hooks so as to avoid deforming the rear seat cushion frame.
Pass the rear seat inner belt through the slit in the rear seat cushion, disengage the hook between the rear seat cushion and rear seat back, and remove the rear seat cushion.
| 7. REMOVE REAR SEAT BACK ASSEMBLY |
Using "Torx" socket wrench E10, remove the 4 bolts and the rear seat back.

| 8. REMOVE REAR DOOR SCUFF PLATE |
Disengage the 6 claws and remove the rear door scuff plate.

| 9. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP |
Remove the rear door opening trim weatherstrip to the extent that the deck trim side panel and roof side inner garnish can be removed.

| 10. REMOVE REAR DECK TRIM COVER |
for Temper Spare Tire:

Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
for Grand Tire:

Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
| 11. REMOVE DECK TRIM SIDE PANEL ASSEMBLY |
Remove the belt of the rear seat outer belt from the rear seat shoulder belt hanger.

Remove the bolt.

Disengage the clip and remove the anchor plate of the rear seat outer belt.
for RH side:

Remove the 3 screws.
Disengage the 3 clips and the 6 claws and remove the deck trim side panel.
for LH side:

Remove the 3 screws.
Disengage the 3 clips and the 6 claws.
Disconnect the luggage compartment room light connector and remove the deck trim side panel.
| 12. REMOVE REAR SEAT SHOULDER BELT HANGER |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the rear seat shoulder belt hanger.

| 13. REMOVE ROOF SIDE INNER GARNISH |
for RH Side (w/ Curtain Shield Airbag):

- NOTICE:
- Replace the special clip with a new one because it is damaged when roof side inner garnish is removed.
Disengage the 5 clips.
Pass the rear seat outer and rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
for RH Side (w/o Curtain Shield Airbag):

Disengage the 5 clips.
Pass the rear seat outer and rear center seat outer belts through the slit in the roof side inner garnish and remove the roof side inner garnish.
for LH Side (w/ Curtain Shield Airbag):

- NOTICE:
- Replace the special clip with a new one because it is damaged when the roof side inner garnish is removed.
Disengage the 5 clips.
Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
for LH Side (w/o Curtain Shield Airbag):

Disengage the 5 clips.
Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
| 14. REMOVE REAR SEAT OUTER BELT ASSEMBLY |
Remove the bolt and the through anchor.

Remove the bolt, the 2 hooks and the retractor.

| 15. REMOVE SEAT BELT HOLE SEAL |
Disengage the 2 claws and remove the seat belt hole seal.

