2005-2008 Yaris · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built Nov 2005 – Dec 2005

Versions by build date: Nov 2005 – Dec 2005 from Jan 2006

CAUTION:
Wear protective gloves. Sharp surfaces on the front seat adjuster frame could cause injuries to your hands.

HINT:
The procedure described below is for the driver side of LHD. Use the same procedure for both the front passenger and driver sides of LHD, unless otherwise specified.


1. INSTALL FRONT SEAT CUSHION LOWER INNER SHIELD (w/ Vertical Adjuster)

  1. B126910
    Engage the claw and stud bolt and install the front seat cushion inner shield.

  1. Using "Torx" socket wrench T25, tighten the screw.


2. INSTALL FRONT SEAT CUSHION LOWER OUTER SHIELD (w/ Vertical Adjuster)

  1. B126909
    Engage the claw and stud bolt and install the front seat cushion lower outer shield.

  1. Using "Torx" socket wrench T25, tighten the screw.


3. INSTALL FRONT SEATBACK COVER PAD

  1. B126908
    Install the front seatback cover pad and engage the 2 hooks.

  1. Install the 2 pieces of hook tape.


4. INSTALL FRONT SEAT HEADREST SUPPORT

B126907E02

HINT:
Use the same procedure for both sides.

  1. Align the protruding portion of the front seat headrest support with the installation groove of the front seat adjuster frame.

  1. Engage the 2 claws and install the front seat headrest support.


5. INSTALL FRONT SEAT CUSHION COVER PAD

  1. B126904
    for Driver Side:

    1. Install the front seat cushion cover pad and engage the 2 hooks.

    2. Install the 3 bands.

  1. B126905
    for Front Passenger Side:

    1. Install the front seat cushion cover pad and engage the 2 hooks.

    2. Install the 3 bands.

    3. Engage the claw and install the connector.

  1. B126903
    Engage the 7 hooks.


6. INSTALL FRONT SEAT CUSHION INNER SHIELD

  1. B124384
    Engage the 2 claws and install the front seat cushion inner shield.


7. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B124388E01
    Install the front seat inner belt with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the front seat inner belt over the convex area of the front seat frame adjuster.

  1. B124389
    for Driver Side:

    1. w/ Seat Heater System:

      1. Connect the seat heater connector.

    2. Install the wire harness into the claw of the front seat frame adjuster.

    3. Install the 2 wiring harness clamps.

    4. Engage the claw and install the buckle switch connector.

  1. B124386
    for Front Passenger Side:

    1. w/ Seat Heater System:

      1. Connect the seat heater connector.

    2. Connect the occupant detection sensor connector.

    3. Install the wiring harness into the claw of the front seat frame adjuster.

    4. Install the 2 wiring harness clamps.

    5. Engage the claw and install the buckle switch connector.


8. INSTALL FRONT SEAT CUSHION OUTER SHIELD

  1. B124385
    Engage the 4 claws and install the front seat cushion outer shield.

  1. Using "Torx" socket wrench T25, tighten the screw.


9. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B124383
    Engage the 2 claws and install the reclining adjuster release handle.


10. INSTALL RECLINING ADJUSTER KNOB CAP

  1. B124381
    Install the reclining adjuster knob cap.


11. INSTALL VERTICAL SEAT ADJUSTER KNOB (w/ Vertical Adjuster)

  1. B124379
    Using "Torx" socket wrench T30, install the vertical seat adjuster knob with the bolt.


12. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (w/ Vertical Adjuster)

  1. B124378
    Engage the 2 claws and install the vertical seat adjuster knob cap.

← DISASSEMBLY (from Jan 2006)REASSEMBLY (from Jan 2006) →