REASSEMBLY
Removal / installation · Vehicles built from Nov 2005
- CAUTION:
- Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands.
| 1. INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY |
Engage the 2 claws and install the No. 2 seat adjuster control cable.

Connect the 2 cables.
Install the 4 clamps.
| 2. INSTALL REAR SEAT RECLINING COVER |
Engage the 2 claws and install the rear seat reclining cover.

| 3. INSTALL REAR SEATBACK COVER PAD SUB-ASSEMBLY |
Engage the hook and install the rear seatback cover pad.

| 4. INSTALL REAR SEAT HEADREST SUPPORT |
![]() ![]() |
- HINT:
- Use the same procedure for both sides.
Align the protruding portion of the rear seat headrest support with the installation groove of the rear seat adjuster.
Engage the 2 claws and install the rear seat headrest support.
| 5. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY |
Install the rear seatback board.

Engage the 2 hooks.

| 6. INSTALL REAR SEAT RECLINING OUTER COVER |
Engage the 3 claws and install the rear seat reclining outer cover.

| 7. INSTALL REAR SEAT INNER BELT ASSEMBLY |
Insert the hook into the rear seat back frame and install the rear seat inner belt with the bolt.

- Torque:
- 42 N*m{ 430 kgf*cm , 31 ft.*lbf }
Install the belt into the rear seatback band.
| 8. INSTALL REAR SEAT RECLINING INNER COVER |
Engage the claw and install the rear seat reclining inner cover.

Using "Torx" socket wrench T25, tighten the screw.
| 9. INSTALL REAR SEAT CUSHION UNDER COVER |
Engage the 4 claws and install the rear seat cushion under cover.

Engage the 4 clips and install the rear seatback cover pad.

| 10. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY |
Install the rear seat lock control lever with the screw.

Install the cover.

| 11. INSTALL REAR SEAT HEADREST ASSEMBLY |
Push in the lock button of the rear seat headrest support and install the rear seat headrest.

| 12. INSTALL REAR SEAT LEG SUB-ASSEMBLY |
Engage the 4 claws and install the 4 retainers.

Using "Torx" socket wrench T40, install the rear seat leg with the 2 bolts.

- Torque:
- 21 N*m{ 215 kgf*cm , 16 ft.*lbf }
| 13. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY |
Engage the 8 hooks and install the rear seat cushion cover pad.

| 14. INSTALL REAR SEAT CUSHION SIDE INNER COVER |
Engage the claw and install the rear seat cushion side inner cover.

Engage the 2 claws and install the 2 rear seat cushion hinge retainers.

| 15. INSTALL REAR SEAT CUSHION SIDE OUTER COVER |
- HINT:
- Use the same procedure as for the LH side.
| 16. INSTALL REAR SEAT CUSHION ASSEMBLY |
Using "Torx" socket wrench T40, install the rear seat cushion with the 2 bolts.

- Torque:
- 21 N*m{ 215 kgf*cm , 16 ft.*lbf }
| 17. INSTALL REAR SEAT CUSHION OUTER COVER |
Engage the 3 claws and install the rear seat cushion outer cover.

| 18. INSTALL REAR SEAT CUSHION INNER COVER |
Engage the 4 claws and install the rear seat cushion inner cover.


