2005-2008 Yaris · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSPECT 1ST GEAR THRUST CLEARANCE

C080538
  1. Using a feeler gauge, measure the 1st gear thrust clearance.

    Standard clearance:
    0.10 to 0.40 mm (0.0039 to 0.0158 in.)

    Maximum clearance:
    0.40 mm (0.0158 in.)

    If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear or transmission clutch hub No. 1.


2. INSPECT 2ND GEAR THRUST CLEARANCE

C068312
  1. Using a dial indicator, measure the 2nd gear thrust clearance.

    Standard clearance:
    0.10 to 0.45 mm (0.0039 to 0.0177 in.)

    Maximum clearance:
    0.45 mm (0.0177 in.)

    If the clearance exceeds the maximum, replace transmission clutch hub No. 1, the 2nd gear or 3rd driven gear.


3. INSPECT 1ST GEAR RADIAL CLEARANCE

C068309
  1. Using a dial indicator, measure the 1st gear radial clearance between the gear and shaft.

    Standard clearance:
    KOYO made bearing:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made bearing:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 1st gear and 1st gear needle roller bearing.


4. INSPECT 2ND GEAR RADIAL CLEARANCE

C068254
  1. Using a dial indicator, measure the 2nd gear radial clearance between the gear and shaft.

    Standard clearance:
    KOYO made:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 2nd gear and 2nd gear needle roller bearing.


5. REMOVE 4TH DRIVEN GEAR

C080539E02
  1. Using SST and a press, remove the output shaft rear bearing and 4th driven gear from the output shaft.

    SST
    09950-00020  


6. REMOVE OUTPUT GEAR SPACER

C068005
  1. Remove the output gear spacer from the output shaft.


7. REMOVE 2ND GEAR

G027264E02
  1. Using SST and a press, remove the 3rd driven gear with 2nd gear from the output shaft.

    SST
    09950-00020  


8. REMOVE 2ND GEAR NEEDLE ROLLER BEARING

C080541
  1. Remove the 2nd gear needle roller bearing and 2nd gear bearing spacer from the output shaft.


9. REMOVE SYNCHRONIZER RING NO. 1 (FOR 2ND GEAR)

C120730
  1. Remove synchronizer ring No. 1 from the output shaft.


10. REMOVE 1ST GEAR

C080543
  1. Using 2 screwdrivers and a hammer, remove the clutch hub No. 1 shaft snap ring from the output shaft.

    HINT:
    Use a shop rag or piece of cloth to keep the shaft snap ring from flying off.

  1. C080544E02
    Using SST and a press, remove the clutch hub No. 1 assembly and 1st gear from the output shaft.
    SST
    09950-00020  

    NOTICE:
    1. Do not tighten SST excessively.
    2. Support the input shaft by hand to prevent it from dropping off.


11. REMOVE SYNCHRONIZER RING NO. 1 (FOR 1ST GEAR)

C080465
  1. Remove synchronizer ring No. 1 from the 1st gear.


12. REMOVE 1ST GEAR NEEDLE ROLLER BEARING

C068012
  1. Remove the 1st gear needle roller bearing from the output shaft.


13. REMOVE 1ST GEAR THRUST WASHER

C068013
  1. Remove the 1st gear thrust washer from the output shaft.


14. REMOVE 1ST GEAR THRUST WASHER PIN OR BALL

C068014
  1. Remove the 1st gear thrust washer pin or ball from the output shaft.


15. REMOVE REVERSE GEAR

C068015
  1. Remove the reverse gear, 3 synchromesh shifting keys and 3 synchromesh shifting key springs from transmission clutch hub No. 1.

    NOTICE:
    Use a shop rag or piece of cloth to keep the shifting key and shifting key spring from flying off.

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →