REASSEMBLY
Removal / installation · Vehicles built from Nov 2005
| 1.
INSTALL REVERSE GEAR |
 |
Coat the reverse gear with gear oil and install it onto transmission clutch hub No. 1.
- NOTICE:
- Orient the reverse gear and transmission clutch hub No. 1 correctly.
Install the 3 synchromesh shifting key springs and 3 synchromesh keys onto transmission clutch hub No. 1.
| 2.
INSTALL 1ST GEAR THRUST WASHER PIN OR BALL |
 |
Coat the 1st gear thrust washer pin or ball with MP grease, and install it onto the output shaft.
| 3.
INSTALL 1ST GEAR THRUST WASHER |
 |
Coat the 1st gear thrust washer with gear oil and install it onto the output shaft.
| 4.
INSTALL 1ST GEAR NEEDLE ROLLER BEARING |
 |
Coat the 1st gear needle roller bearing with gear oil and install it onto the output shaft.
| 5.
INSTALL 1ST GEAR |
 |
Coat the 1st gear with gear oil and install it onto the output shaft.
| 6.
INSTALL SYNCHRONIZER RING NO. 1 (FOR 1ST GEAR) |
 |
Coat synchronizer ring No. 1 with gear oil and install it onto the 1st gear.
| 7.
INSTALL TRANSMISSION CLUTCH HUB NO. 1 |
 |
Using SST and a press, install transmission clutch hub No. 1 onto the output shaft.
- SST
- 09316-60011
(09316-00031)
- HINT:
- The 1st gear can be turned.
- While checking that the 1st gear thrust washer pin or ball is inserted into the groove of the 1st gear thrust washer, press and fit clutch hub No. 1.
- Select a snap ring that will allow minimum axial play.
- Standard clearance:
- 0.1 mm (0.039 in.) or less
- Snap ring thickness:
Mark
|
Thickness mm (in.)
|
Mark
|
Thickness mm (in.)
|
A
|
2.50 (0.0984)
|
D
|
2.68 (0.1055)
|
B
|
2.56 (0.1008)
|
E
|
2.74 (0.1079)
|
C
|
2.62 (0.1032)
|
F
|
2.80 (0.1102)
|
Using a brass bar and a hammer, install the snap ring onto the output shaft.
- NOTICE:
- Do not damage the journal surface of the output shaft.
| 8.
INSTALL 2ND GEAR NEEDLE ROLLER BEARING |
 |
Coat the 2nd gear needle roller bearing and 2nd gear bearing spacer with gear oil, and install them onto the output shaft.
| 9.
INSTALL SYNCHRONIZER RING NO. 1 (FOR 2ND GEAR) |
 |
Coat synchronizer ring No. 1 with gear oil and install it onto the 2nd gear.
| 10.
INSTALL 2ND GEAR |
 |
Coat the 2nd gear with gear oil and install it onto the output shaft.
| 11.
INSTALL 3RD DRIVEN GEAR |
 |
Using SST and a press, install the 3rd driven gear onto the output shaft.
- SST
- 09316-60011
(09316-00031)
| 12.
INSTALL OUTPUT GEAR SPACER |
 |
Install the output gear spacer onto the output shaft.
| 13.
INSTALL 4TH DRIVEN GEAR |
 |
Using SST and a press, install the 4th driven gear onto the output shaft.
- SST
- 09612-22011
| 14.
INSTALL OUTPUT SHAFT REAR BEARING |
 |
Using SST and a press, install the output shaft rear bearing onto the output shaft.
- SST
- 09612-22011
| 15.
INSPECT 2ND GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the 2nd gear radial clearance between the gear and shaft.
- Standard clearance:
- KOYO made:
- 0.015 to 0.058 mm (0.0006 to 0.00023 in.)
- NSK made:
- 0.015 to 0.056 mm (0.0006 to 0.0022 in.)
- Maximum clearance:
- KOYO made:
- 0.058 mm (0.0023 in.)
- NSK made:
- 0.056 mm (0.0022 in.)
If the clearance exceeds the maximum, replace the 2nd gear or 2nd gear needle roller bearing.
| 16.
INSPECT 1ST GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the 1st gear radial clearance between the gear and shaft.
- Standard clearance:
- KOYO made:
- 0.015 to 0.058 mm (0.0006 to 0.00023 in.)
- NSK made:
- 0.015 to 0.056 mm (0.0006 to 0.0022 in.)
- Maximum clearance:
- KOYO made:
- 0.058 mm (0.0023 in.)
- NSK made:
- 0.056 mm (0.0022 in.)
If the clearance exceeds the maximum, replace the 1st gear or 1st gear needle roller bearing.
| 17.
INSPECT 2ND GEAR THRUST CLEARANCE |
 |
Using a dial indicator, measure the 2nd gear thrust clearance.
- Standard clearance:
- 0.10 to 0.45 mm (0.0039 to 0.0177 in.)
- Maximum clearance:
- 0.45 mm (0.0177 in.)
If the clearance exceeds the maximum, replace transmission clutch hub No. 1, the 2nd gear or 3rd driven gear.
| 18.
INSPECT 1ST GEAR THRUST CLEARANCE |
 |
Using a feeler gauge, measure the 1st gear thrust clearance.
- Standard clearance:
- 0.10 to 0.40 mm (0.0039 to 0.0158 in.)
- Maximum clearance:
- 0.40 mm (0.0158 in.)
If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear or transmission clutch hub No. 1.