DISASSEMBLY
Removal / installation · Vehicles built from Aug 2005
| 1.
INSPECT 4TH GEAR THRUST CLEARANCE |
 |
Using a feeler gauge, measure the 4th gear thrust clearance.
- Standard clearance:
- 0.1 to 0.55 mm (0.0039 to 0.0217 in.)
- Maximum clearance:
- 0.55 mm (0.0217 in.)
If the clearance exceeds the maximum, replace transmission clutch hub No. 2, the 4th gear or input shaft rear radial ball bearing.
| 2.
INSPECT 3RD GEAR THRUST CLEARANCE |
 |
Using a dial gauge, measure the 3rd gear thrust clearance.
- Standard clearance:
- 0.1 to 0.35 mm (0.0039 to 0.0138 in.)
- Maximum clearance:
- 0.35 mm (0.0138 in.)
If the clearance exceeds the maximum, replace transmission clutch hub No. 2, the 3rd gear or input shaft.
| 3.
INSPECT 4TH GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the 4th gear radial clearance between the gear and shaft.
- Standard clearance:
- 0.009 to 0.050 mm (0.0004 to 0.0020 in.)
- Maximum clearance:
- 0.050 mm (0.0020 in.)
If the clearance exceeds the maximum, replace the 4th gear, 4th gear needle roller bearing or the input shaft.
| 4.
INSPECT 3RD GEAR RADIAL CLEARANCE |
 |
Using a dial gauge, measure the 3rd gear radial clearance between the gear and shaft.
- Standard clearance:
- KOYO made bearing:
- 0.015 to 0.058 mm (0.0006 to 0.0023 in.)
- NSK made bearing:
- 0.015 to 0.056 mm (0.0006 to 0.0022 in.)
- Maximum clearance:
- KOYO made:
- 0.058 mm (0.0023 in.)
- NSK made:
- 0.056 mm (0.0022 in.)
If the clearance exceeds the maximum, replace the 3rd gear, 3rd gear needle roller bearing or input shaft.
| 5.
REMOVE 4TH GEAR |
 |
Using 2 screwdrivers and a hammer, remove the input shaft rear bearing shaft snap ring from the input shaft.
- HINT:
- Use a shop rag or piece of cloth to keep the snap ring from flying off.
- Using SST and a press, remove the input shaft rear radial ball bearing and 4th gear from the input shaft.
- SST
- 09950-00020
- HINT:
- Do not tighten SST excessively.
- Support the input shaft assembly by hand to prevent it from dropping off.
| 6.
REMOVE 4TH GEAR NEEDLE ROLLER BEARING |
 |
Remove the 4th gear needle roller bearing and 4th gear bearing spacer from the input shaft.
| 7.
REMOVE 4TH GEAR SYNCHRONIZER RING |
 |
Remove synchronizer ring No. 2 from transmission clutch hub No. 2.
| 8.
REMOVE 3RD GEAR |
 |
Using 2 screwdrivers and a hammer, remove the clutch hub No. 2 setting shaft snap ring from the input shaft.
- HINT:
- Use a shop rag or piece of cloth to keep the snap ring from flying off.
- Using SST and a press, remove transmission clutch hub No. 2 and the 3rd gear from the input shaft.
- SST
- 09950-00020
- NOTICE:
- Do not tighten SST excessively.
- Support the input shaft by hand to prevent it from dropping off.
| 9.
REMOVE 3RD GEAR SYNCHRONIZER RING |
 |
Remove synchronizer ring No. 2 from the 3rd gear.
| 10.
REMOVE 3RD GEAR NEEDLE ROLLER BEARING |
 |
Remove the 3rd gear needle roller bearing from the input shaft.
| 11.
REMOVE TRANSMISSION HUB SLEEVE NO.2 |
 |
Remove transmission hub sleeve No. 2, the 3 shifting keys and 3 shifting key springs from transmission clutch hub No. 2.
- NOTICE:
- Use a shop rag or piece of cloth to keep the shifting key and shifting key spring from flying off.