2005-2008 Yaris · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2006


1. INSPECT 4TH GEAR THRUST CLEARANCE

C080557
  1. Using a feeler gauge, measure the 4th gear thrust clearance.

    Standard clearance:
    0.1 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 4th gear or input shaft rear radial ball bearing.


2. INSPECT 3RD GEAR THRUST CLEARANCE

C067816
  1. Using a dial gauge, measure the 3rd gear thrust clearance.

    Standard clearance:
    0.1 to 0.35 mm (0.0039 to 0.0138 in.)

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 3rd gear or input shaft.


3. INSPECT 4TH GEAR RADIAL CLEARANCE

C080558
  1. Using a dial indicator, measure the 4th gear radial clearance between the gear and shaft.

    Standard clearance:
    0.009 to 0.050 mm (0.0004 to 0.0020 in.)

    Maximum clearance:
    0.050 mm (0.0020 in.)

    If the clearance exceeds the maximum, replace the 4th gear, 4th gear needle roller bearing or input shaft.


4. INSPECT 3RD GEAR RADIAL CLEARANCE

C067815
  1. Using a dial gauge, measure the 3rd gear radial clearance between the gear and shaft.

    Standard clearance:
    KOYO made bearing:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made bearing:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 3rd gear, 3rd gear needle roller bearing or input shaft.


5. REMOVE 4TH GEAR

C080559
  1. Using 2 screwdrivers and a hammer, remove the input shaft rear bearing shaft snap ring from the input shaft.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. Q004983E01
    Using SST and a press, remove the input shaft rear radial ball bearing and 4th gear from the input shaft.
    SST
    09950-00020  

    HINT:
    1. Do not tighten SST excessively.
    2. Support the input shaft assembly by hand to prevent it from dropping off.


6. REMOVE 4TH GEAR NEEDLE ROLLER BEARING

C080560
  1. Remove the 4th gear needle roller bearing and 4th gear bearing spacer from the input shaft.


7. REMOVE 4TH GEAR SYNCHRONIZER RING

C080561
  1. Remove the No. 2 synchronizer ring from the No. 2 transmission clutch hub.


8. REMOVE 3RD GEAR

C067821
  1. Using 2 screwdrivers and a hammer, remove the clutch hub No. 2 setting shaft snap ring from the input shaft.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. CM00064E01
    Using SST and a press, remove the No. 2 transmission clutch hub and the 3rd gear from the input shaft.
    SST
    09950-00020  

    NOTICE:
    1. Do not tighten SST excessively.
    2. Support the input shaft by hand to prevent it from dropping off.


9. REMOVE 3RD GEAR SYNCHRONIZER RING

C080455
  1. Remove the No. 2 synchronizer ring from the 3rd gear.


10. REMOVE 3RD GEAR NEEDLE ROLLER BEARING

C067823
  1. Remove the 3rd gear needle roller bearing from the input shaft.


11. REMOVE NO. 2 TRANSMISSION HUB SLEEVE

C067832
  1. Remove the No. 2 transmission hub sleeve, the 3 shifting keys and 3 shifting key springs from No. 2 transmission clutch hub.

    NOTICE:
    Use a shop rag or piece of cloth to keep the shifting key and shifting key spring from flying off.

← COMPONENTS (from Nov 2006)INSPECTION (from Nov 2006) →