2005-2008 Yaris · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2006


1. INSTALL NO. 2 TRANSMISSION HUB SLEEVE

C069660
  1. Coat the No. 2 transmission hub sleeve with gear oil, and install it onto the No. 2 transmission clutch hub.

    NOTICE:
    Orient the No. 2 transmission hub sleeve and No. 2 transmission clutch hub correctly.

  1. Using a screwdriver, install the 3 synchromesh key springs with 3 synchromesh shifting keys onto the No. 2 transmission clutch hub.


2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING

C067823
  1. Coat the 3rd gear needle roller bearing with gear oil and install it onto the input shaft.


3. INSTALL 3RD GEAR

D032763
  1. Coat the 3rd gear with gear oil and install it onto the input shaft.


4. INSTALL 3RD GEAR SYNCHRONIZER RING

D031159E01
  1. Coat the 3rd gear synchronizer ring with gear oil and install it onto the 3rd gear.


5. INSTALL NO. 2 TRANSMISSION CLUTCH HUB

C080563E01
  1. Using SST and a press, install the No. 2 transmission clutch hub onto the input shaft.

    SST
    09316-60011   (09316-00021)

    NOTICE:
    Fit the synchromesh shifting key into the groove of the synchronizer ring correctly.

  1. C067837
    Select a snap ring that will allow minimum axial play.

    Standard clearance:
    0.1 mm (0.0039 in.) or less

    Snap ring thickness:
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    0
    2.30 (0.0906)
    3
    2.48 (0.0976)
    1
    2.36 (0.0929)
    4
    2.54 (0.1000)
    2
    2.42 (0.0953)
    5
    2.60 (0.1024)

  1. Using a brass bar and a hammer, install the snap ring onto the input shaft.


6. INSTALL 4TH GEAR SYNCHRONIZER RING

C080464E02
  1. Coat the 4th gear synchronizer ring with gear oil and install it onto the No. 2 transmission clutch hub.


7. INSTALL 4TH GEAR NEEDLE ROLLER BEARING

C080560
  1. Coat the 4th gear needle roller bearing and 4th gear bearing spacer with gear oil and install them onto No. 2 transmission clutch hub.


8. INSTALL 4TH GEAR

C080564
  1. Coat the 4th gear with gear oil and install it onto the input shaft.


9. INSTALL INPUT SHAFT REAR RADIAL BALL BEARING

C080565E01
  1. Using SST and a press, install the input shaft rear radial ball bearing onto the input shaft.

    SST
    09608-04031  

  1. C080566
    Select a snap ring that will allow minimum axial play.

    Standard clearance:
    0.1 mm (0.0039 in.) or less

    Snap ring thickness:
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    A
    2.29 (0.0901)
    D
    2.47 (0.0972)
    B
    2.35 (0.0925)
    E
    2.53 (0.0996)
    C
    2.41 (0.0948)
    F
    2.59 (0.1019)

  1. Using a brass bar and a hammer, install the snap ring onto the input shaft.

    NOTICE:
    Do not damage the journal surface of the snap ring.


10. INSPECT 3RD GEAR RADIAL CLEARANCE

C067815
  1. Using a dial gauge, measure the 3rd gear radial clearance.

    Standard clearance:
    KOYO made:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 3rd gear, 3rd gear needle roller bearing or input shaft.


11. INSPECT 4TH GEAR RADIAL CLEARANCE

C080558
  1. Using a dial gauge, measure the 4th gear radial clearance.

    Standard clearance:
    0.009 to 0.050 mm (0.0004 to 0.0020 in.)

    Maximum clearance:
    0.050 mm (0.0020 in.)

    If the clearance exceeds the maximum, replace the 4th gear, 4th gear needle roller bearing or input shaft.


12. INSPECT 3RD GEAR THRUST CLEARANCE

C067816
  1. Using a dial gauge, measure the 3rd gear thrust clearance.

    Standard clearance:
    0.1 to 0.35 mm (0.0039 to 0.0138 in.)

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 3rd gear or input shaft.


13. INSPECT 4TH GEAR THRUST CLEARANCE

C080557
  1. Using a feeler gauge, measure the 4th gear thrust clearance.

    Standard clearance:
    0.1 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 4th gear or input shaft rear radial ball bearing.

← INSPECTION (from Nov 2006)COMPONENTS (from Nov 2006) →