DISASSEMBLY
Removal / installation · Vehicles built from Nov 2005
| 1. REMOVE MANUAL TRANSMISSION FILLER PLUG |
![]() ![]() |
Remove the manual transmission filler plug and gasket from the manual transmission case.
| 2. REMOVE DRAIN PLUG SUB-ASSEMBLY |
![]() ![]() |
Remove the drain plug sub-assembly and gasket from the manual transmission case.
| 3. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY |
Remove the bolt and speedometer driven hole cover sub-assembly from the transaxle case.
Remove the O-ring from the speedometer driven hole cover sub-assembly.
| 4. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY |
![]() ![]() |
Separate the back-up light switch wire harness from the 2 clamps.
Using SST, remove the back-up light switch assembly and gasket from the manual transmission case.
- SST
- 09817-16011
| 5. REMOVE SELECTING BELL CRANK ASSEMBLY |
![]() ![]() |
Remove the 2 bolts and nut and remove the selecting bell crank assembly from the manual transmission case.
Remove the control shift lever bush.
| 6. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER |
![]() ![]() |
Remove the nut and spring washer.
Using a brass bar and a hammer, remove the lock pin.

Remove the floor shift control shift lever.
| 7. REMOVE SHIFT LEVER DAMPER |
![]() ![]() |
Remove the nut and spring washer.
Using a brass bar and a hammer, remove the lock pin.

Remove the shift lever damper.
| 8. FIX MANUAL TRANSAXLE ASSEMBLY |
![]() ![]() |
Place the manual transaxle assembly on wooden blocks.
| 9. REMOVE LOCK BALL ASSEMBLY NO.1 |
![]() ![]() |
Remove lock ball assembly No. 1 from the manual transmission case.
| 10. REMOVE SHIFT GATE PIN |
![]() ![]() |
Remove the shift gate pin and washer from the transmission case.
| 11. REMOVE CONTROL SHAFT COVER |
![]() ![]() |
Remove the 4 bolts, control shaft cover and gasket from the manual transmission case.
| 12. REMOVE CONTROL SHAFT COVER OIL SEAL |
![]() ![]() |
Using a screwdriver, remove the control shaft cover oil seal from the control shaft cover.
| 13. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY |
![]() ![]() |
Remove the shift and select lever shaft assembly from the transmission case.
| 14. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY |
![]() ![]() |
Remove the 9 bolts.
Using a plastic hammer, carefully tap the projections of the manual transmission case cover sub-assembly to remove the manual transmission case cover from the manual transmission case.

- NOTICE:
- Do not damage the manual transmission case.
| 15. REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT |
![]() ![]() |
Using a chisel and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.
Engage 2 gears simultaneously to lock the transmission.

Remove the manual transmission output shaft rear set nut.
Disengage the 2 gears.
| 16. REMOVE GEAR SHIFT FORK NO.3 |
![]() ![]() |
Remove the gear shift fork lock bolt from gear shift fork No. 3.
Remove transmission hub sleeve No. 3 with gear shift fork No. 3 from transmission clutch hub No. 3.

| 17. INSPECT 5TH GEAR THRUST CLEARANCE |
![]() ![]() |
Using a dial indicator, measure the 5th gear thrust clearance.
- Standard clearance:
- 0.10 to 0.55 mm (0.0039 to 0.0217 in.)
- Maximum clearance:
- 0.55 mm (0.0217 in.)
| 18. INSPECT 5TH GEAR RADIAL CLEARANCE |
![]() ![]() |
Using a dial indicator, measure the 5th gear radial clearance.
- Standard clearance:
- KOYO made:
- 0.015 to 0.058 mm (0.0006 to 0.0023 in.)
- NSK made:
- 0.015 to 0.056 mm (0.0006 to 0.0022 in.)
- Maximum clearance:
- KOYO made:
- 0.058 mm (0.0023 in.)
- NSK made:
- 0.056 mm (0.0022 in.)
| 19. REMOVE TRANSMISSION CLUTCH HUB NO.3 |
![]() ![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring.
- HINT:
- Use a shop rag or piece of cloth to keep the snap ring from flying off.
Using SST, remove transmission clutch hub No. 3, the 5th gear and synchronizer ring No. 3 from the input shaft.

- SST
- 09950-40011
(09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04011)
09950-60010 (09951-00180)
Remove the 3 synchromesh shifting keys and 2 synchromesh shifting key springs from transmission clutch hub No. 3.

| 20. REMOVE 5TH GEAR NEEDLE ROLLER BEARING |
![]() ![]() |
Remove the 5th gear needle roller bearing and 5th gear bearing spacer from the input shaft.
| 21. REMOVE 5TH DRIVEN GEAR |
![]() ![]() |
Using SST, remove the 5th driven gear from the output shaft.
- SST
- 09950-30012
(09951-03010, 09953-03010, 09954-03010, 09955-03021)
09950-60010 (09951-00180)
| 22. REMOVE BEARING RETAINER REAR |
![]() ![]() |
Remove the 5 bolts and bearing retainer rear from the manual transmission case.
| 23. REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING |
![]() ![]() |
Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft.
| 24. REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING |
![]() ![]() |
Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft.
| 25. REMOVE REVERSE IDLER GEAR SHAFT BOLT |
![]() ![]() |
Remove the reverse idler gear shaft bolt and reverse idler gear shaft gasket from the manual transmission case.
| 26. REMOVE SHIFT FORK SHAFT SHAFT SNAP RING |
![]() ![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring from gear shift fork shaft No. 2.
- HINT:
- Use a shop rag or piece of cloth to keep the snap ring from flying off.
| 27. REMOVE SHIFT DETENT BALL |
![]() ![]() |
Using a hexagon wrench, remove the 2 shift detent ball plugs from the manual transmission case.
Using a magnetic finger, remove the 2 shift detent ball spring seats No. 1, 2 shift detent ball springs and 2 shift detent balls from the manual transmission case.

Using a hexagon wrench, remove the shift detent ball plug from the front transaxle case.

Using a magnetic finger, remove the seat, spring and ball from the front transaxle case.

| 28. REMOVE LOCK BALL ASSEMBLY NO.2 |
![]() ![]() |
Using a hexagon wrench, remove lock ball assembly No. 2 from the manual transmission case.
| 29. REMOVE MANUAL TRANSMISSION CASE |
![]() ![]() |
Remove the 3 bolts from the front transaxle case.
Remove the 13 bolts from the manual transmission case.

Using a brass bar and a hammer, carefully tap the projections of the manual transmission case to remove the transmission case from the transaxle case.

- NOTICE:
- Do not damage the manual transmission case and transaxle case.
| 30. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY |
![]() ![]() |
Remove the reverse idler gear sub-assembly, thrust washer and reverse idler gear shaft from the front transaxle case.
| 31. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY |
![]() ![]() |
Remove the 2 bolts and reverse shift arm bracket assembly from the front transaxle case.
| 32. REMOVE GEAR SHIFT FORK SHAFT NO.2 |
![]() ![]() |
Remove the 2 bolts from gear shift fork No. 2 and gear shift head No. 1.
Remove gear shift fork shaft No. 2 and gear shift head No. 1 from the front transaxle case.

| 33. REMOVE GEAR SHIFT FORK SHAFT NO.1 |
![]() ![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring.
- HINT:
- Use a shop rag or piece of cloth to keep the snap ring from flying off.
Remove the shift fork set bolt and gear shift fork shaft No. 1 from gear shift fork No. 1.

Remove gear shift fork No. 1.

| 34. REMOVE GEAR SHIFT FORK SHAFT NO.3 |
![]() ![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring from gear shift fork shaft No. 3.
- HINT:
- Use a shop rag or piece of cloth to keep the snap ring from flying off.
Remove shift fork shaft No. 3 together with the reverse shift fork and gear shift fork No. 2 from the manual transaxle case.

Using a magnetic finger, remove the 2 reverse shift fork balls from the reverse shift fork.

Using 2 screwdrivers and a hammer, tap the snap ring out of shift fork shaft No. 3.

- HINT:
- Use a shop rag or piece of cloth to keep the snap ring from flying off.
Remove the reverse shift fork from gear shift fork shaft No. 3.
| 35. REMOVE INPUT SHAFT ASSEMBLY |
![]() ![]() |
Remove the input shaft assembly and output shaft assembly from the front transaxle case.
| 36. REMOVE DIFFERENTIAL CASE ASSEMBLY |
![]() ![]() |
Remove the differential case assembly from the front transaxle case.
| 37. REMOVE MANUAL TRANSAXLE CASE RECEIVER |
![]() ![]() |
Remove the bolt and manual transaxle case receiver from the front transaxle case.
| 38. REMOVE REVERSE RESTRICT PIN ASSEMBLY |
![]() ![]() |
Using a hexagon wrench, remove the reverse restrict pin plug from the manual transmission case.
Using a pin punch (φ5 mm) and a hammer, drive out the slotted spring pin and remove the reverse restrict pin assembly from the manual transmission case.

| 39. REMOVE OIL RECEIVER PIPE NO. 1 |
![]() ![]() |
Remove the bolt and oil receiver pipe No. 1 from the manual transmission case.
- NOTICE:
- Do not damage oil receiver pipe No. 1.
| 40. REMOVE OIL RECEIVER PIPE NO. 2 |
![]() ![]() |
Remove the bolt and oil receiver pipe No. 2 from the manual transmission case.
- NOTICE:
- Do not damage oil receiver pipe No. 2.
| 41. REMOVE BEARING LOCK PLATE |
![]() ![]() |
Remove the bolt and bearing lock plate from the front transaxle case.
| 42. REMOVE TRANSMISSION MAGNET |
![]() ![]() |
Remove the transmission magnet from the front transaxle case.
| 43. REMOVE INPUT SHAFT FRONT BEARING |
![]() ![]() |
Using SST, remove the input shaft front bearing from the front transaxle case.
- SST
- 09612-65014
(09612-01050, 09612-01060)
| 44. REMOVE FRONT TRANSAXLE CASE OIL SEAL |
![]() ![]() |
Using a screwdriver, remove the front transaxle case oil seal from the transaxle case.
| 45. REMOVE OUTPUT SHAFT FRONT BEARING |
![]() ![]() |
Using SST, remove the output shaft front bearing from the front transaxle case.
- SST
- 09308-00010
- NOTICE:
- Do not apply excessive force to the front transaxle case when installing SST.
| 46. REMOVE OUTPUT SHAFT COVER |
![]() ![]() |
Remove the output shaft cover from the front transaxle case.
| 47. REMOVE FR DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() ![]() |
Using SST, remove the front differential case front tapered roller bearing (outer race) and plate washer from the front transaxle case.
- SST
- 09612-65014
(09612-01040, 09612-01050)
Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.

- SST
- 09950-00020
09950-00030
09950-40011 (09957-04010)
09950-60010 (09951-00360)
- NOTICE:
- Do not damage the bearing.
| 48. REMOVE TRANSAXLE CASE OIL SEAL |
![]() ![]() |
Using SST and a hammer, remove the transaxle case oil seal from the front transaxle case.
- SST
- 09950-60010
(09951-00530)
09950-70010 (09951-07150)
| 49. REMOVE FR DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() ![]() |
Using SST, remove the front differential case rear tapered roller bearing (outer race) and plate washer from the transmission case.
- SST
- 09612-65014
(09612-01040, 09612-01050)
Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.

- SST
- 09950-40011
(09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010 (09951-00360)
| 50. REMOVE TRANSMISSION CASE OIL SEAL |
![]() ![]() |
Using SST and a hammer, drive out the transmission case oil seal from the manual transmission case.
- SST
- 09950-60010
(09951-00530)
09950-70010 (09951-07150)
| 51. REMOVE SHIFT AND SELECT LEVER SHAFT OIL SEAL |
![]() ![]() |
Using a screwdriver and hammer, remove the shift and select lever shaft oil seal.
| 52. REMOVE SHIFT AND SELECT LEVER SHAFT SLIDE BALL BEARING |
![]() ![]() |
Using SST and a hammer, remove the shift and select lever shaft slide ball bearing.
- SST
- 09950-60010
(09951-00220)
09950-70010 (09951-07200)



















































