2005-2008 Yaris · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2006


1. REMOVE MANUAL TRANSMISSION FILLER PLUG

C080549
  1. Remove the manual transmission filler plug and gasket from the manual transmission case.


2. REMOVE DRAIN PLUG SUB-ASSEMBLY

C080550
  1. Remove the drain plug sub-assembly and gasket from the manual transmission case.


3. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and speedometer driven hole cover sub-assembly from the transaxle case.

  1. Remove the O-ring from the speedometer driven hole cover sub-assembly.


4. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

C120749E01
  1. Separate the back-up light switch wire harness from the 2 clamps.

  1. Using SST, remove the back-up light switch assembly and gasket from the manual transmission case.

    SST
    09817-16011  


5. REMOVE SELECTING BELL CRANK ASSEMBLY

C120750
  1. Remove the 2 bolts and nut and remove the selecting bell crank assembly from the manual transmission case.

  1. Remove the control shift lever bush.


6. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER

C120748
  1. Remove the nut and spring washer.

  1. C120747
    Using a brass bar and a hammer, remove the lock pin.

  1. Remove the floor shift control shift lever.


7. REMOVE SHIFT LEVER DAMPER

C120746
  1. Remove the nut and spring washer.

  1. C120745
    Using a brass bar and a hammer, remove the lock pin.

  1. Remove the shift lever damper.


8. FIX MANUAL TRANSAXLE ASSEMBLY

C080552E01
  1. Place the manual transaxle assembly on wooden blocks.


9. REMOVE NO. 1 LOCK BALL ASSEMBLY

C120744
  1. Remove the No. 1 lock ball assembly from the manual transmission case.


10. REMOVE SHIFT GATE PIN

C120743
  1. Remove the shift gate pin and washer from the transmission case.


11. REMOVE CONTROL SHAFT COVER

C120742
  1. Remove the 4 bolts, control shaft cover and gasket from the manual transmission case.


12. REMOVE CONTROL SHAFT COVER OIL SEAL

C120741
  1. Using a screwdriver, remove the control shaft cover oil seal from the control shaft cover.


13. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY

C120740
  1. Remove the shift and select lever shaft assembly from the transmission case.


14. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

C080554
  1. Remove the 9 bolts.

  1. C158159
    Using a plastic hammer, carefully tap the projections of the manual transmission case cover sub-assembly to remove the manual transmission case cover from the manual transmission case.

    NOTICE:
    Do not damage the manual transmission case.


15. REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

C080341
  1. Using a chisel and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.

  1. Q006512
    Engage 2 gears simultaneously to lock the transmission.

  1. Remove the manual transmission output shaft rear set nut.

  1. Disengage the 2 gears.


16. REMOVE NO. 3 GEAR SHIFT FORK

C080342
  1. Remove the gear shift fork lock bolt from the No. 3 gear shift fork.

  1. C080343
    Remove the No. 3 transmission hub sleeve with the No. 3 gear shift fork from the No. 3 transmission clutch hub.


17. INSPECT 5TH GEAR THRUST CLEARANCE

C080344
  1. Using a dial indicator, measure the 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, 5th gear or input shaft rear radial ball bearing.


18. INSPECT 5TH GEAR RADIAL CLEARANCE

C080345
  1. Using a dial indicator, measure the 5th gear radial clearance.

    Standard clearance:
    KOYO made:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.


19. REMOVE NO. 3 TRANSMISSION CLUTCH HUB

C080346
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. C080347E01
    Using SST, remove the No. 3 transmission clutch hub, 5th gear and No. 3 synchronizer ring from the input shaft.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04011)
    09950-60010   (09951-00180)

  1. D007737
    Remove the 3 synchromesh shifting keys and 2 synchromesh shifting key springs from the No. 3 transmission clutch hub.


20. REMOVE 5TH GEAR NEEDLE ROLLER BEARING

C080348
  1. Remove the 5th gear needle roller bearing and 5th gear bearing spacer from the input shaft.


21. REMOVE 5TH DRIVEN GEAR

C080349E01
  1. Using SST, remove the 5th driven gear from the output shaft.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03021)
    09950-60010   (09951-00180)


22. REMOVE BEARING RETAINER REAR

C080350E01
  1. Remove the 5 bolts and bearing retainer rear from the manual transmission case.


23. REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING

C080351
  1. Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft.


24. REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING

C080352
  1. Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft.


25. REMOVE REVERSE IDLER GEAR SHAFT BOLT

C067639
  1. Remove the reverse idler gear shaft bolt and reverse idler gear shaft gasket from the manual transmission case.


26. REMOVE SHIFT FORK SHAFT SHAFT SNAP RING

C080353
  1. Using 2 screwdrivers and a hammer, tap out the snap ring from the No. 2 gear shift fork shaft.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.


27. REMOVE SHIFT DETENT BALL

C067634
  1. Using a hexagon wrench, remove the 2 shift detent ball plugs from the manual transmission case.

  1. C067635
    Using a magnetic finger, remove the 2 No. 1 shift detent ball spring seats, 2 shift detent ball springs and 2 shift detent balls from the manual transmission case.

  1. C080354
    Using a hexagon wrench, remove the shift detent ball plug from the front transaxle case.

  1. C080355
    Using a magnetic finger, remove the seat, spring and ball from the front transaxle case.


28. REMOVE NO. 2 LOCK BALL ASSEMBLY

C080356
  1. Using a hexagon wrench, remove the No. 2 lock ball assembly from the manual transmission case.


29. REMOVE MANUAL TRANSMISSION CASE

C080357
  1. Remove the 3 bolts from the front transaxle case.

  1. C080358
    Remove the 13 bolts from the manual transmission case.

  1. C067642
    Using a brass bar and a hammer, carefully tap the projections of the manual transmission case to remove the transmission case from the transaxle case.

    NOTICE:
    Do not damage the manual transmission case and transaxle case.


30. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

C080359
  1. Remove the reverse idler gear sub-assembly, thrust washer and reverse idler gear shaft from the front transaxle case.


31. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY

C080360
  1. Remove the 2 bolts and reverse shift arm bracket assembly from the front transaxle case.


32. REMOVE NO. 2 GEAR SHIFT FORK SHAFT

C080361
  1. Remove the 2 bolts from the No. 2 gear shift fork and No. 1 gear shift head.

  1. C080362E06
    Remove the No. 2 gear shift fork shaft and No. 1 gear shift head from the front transaxle case.


33. REMOVE NO. 1 GEAR SHIFT FORK SHAFT

C080363
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. C080364E04
    Remove the shift fork set bolt and No. 1 gear shift fork shaft from the No. 1 gear shift fork.

  1. C080365E05
    Remove the No. 1 gear shift fork.


34. REMOVE NO. 3 GEAR SHIFT FORK SHAFT

C080366
  1. Using 2 screwdrivers and a hammer, tap out the snap ring from the No. 3 gear shift fork shaft.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. C080367E04
    Remove the No. 3 shift fork shaft together with the reverse shift fork and No. 2 gear shift fork from the manual transaxle case.

  1. C080368
    Using a magnetic finger, remove the 2 reverse shift fork balls from the reverse shift fork.

  1. C080369
    Using 2 screwdrivers and a hammer, tap the snap ring out of the No. 3 shift fork shaft.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. Remove the reverse shift fork from the No. 3 gear shift fork shaft.


35. REMOVE INPUT SHAFT ASSEMBLY

C080586
  1. Remove the input shaft assembly and output shaft assembly from the front transaxle case.


36. REMOVE DIFFERENTIAL CASE ASSEMBLY

C067656
  1. Remove the differential case assembly from the front transaxle case.


37. REMOVE MANUAL TRANSAXLE CASE RECEIVER

C067657
  1. Remove the bolt and manual transaxle case receiver from the front transaxle case.


38. REMOVE REVERSE RESTRICT PIN ASSEMBLY

C080372
  1. Using a hexagon wrench, remove the reverse restrict pin plug from the manual transmission case.

  1. C080373
    Using a pin punch (φ5 mm) and a hammer, drive out the slotted spring pin and remove the reverse restrict pin assembly from the manual transmission case.


39. REMOVE NO. 1 OIL RECEIVER PIPE

C067644
  1. Remove the bolt and No. 1 oil receiver pipe from the manual transmission case.

    NOTICE:
    Do not damage the No. 1 oil receiver pipe.


40. REMOVE NO. 2 OIL RECEIVER PIPE

C080374
  1. Remove the bolt and No. 2 oil receiver pipe from the manual transmission case.

    NOTICE:
    Do not damage the No. 2 oil receiver pipe.


41. REMOVE BEARING LOCK PLATE

C067658
  1. Remove the bolt and bearing lock plate from the front transaxle case.


42. REMOVE TRANSMISSION MAGNET

C067659E09
  1. Remove the transmission magnet from the front transaxle case.


43. REMOVE INPUT SHAFT FRONT BEARING

C081783E01
  1. Using SST, remove the input shaft front bearing from the front transaxle case.

    SST
    09612-65014   (09612-01050, 09612-01060)


44. REMOVE FRONT TRANSAXLE CASE OIL SEAL

C095411
  1. Using a screwdriver, remove the front transaxle case oil seal from the transaxle case.


45. REMOVE OUTPUT SHAFT FRONT BEARING

C082141E01
  1. Using SST, remove the output shaft front bearing from the front transaxle case.

    SST
    09308-00010  

    NOTICE:
    Do not apply excessive force to the front transaxle case when installing SST.


46. REMOVE OUTPUT SHAFT COVER

C067719
  1. Remove the output shaft cover from the front transaxle case.


47. REMOVE FR DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

C081785E01
  1. Using SST, remove the front differential case front tapered roller bearing (outer race) and plate washer from the front transaxle case.

    SST
    09612-65014   (09612-01040, 09612-01050)

  1. G026414E01
    Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.
    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00360)

    NOTICE:
    Do not damage the bearing.


48. REMOVE TRANSAXLE CASE OIL SEAL

C081787E01
  1. Using SST and a hammer, remove the transaxle case oil seal from the front transaxle case.

    SST
    09950-60010   (09951-00530)
    09950-70010   (09951-07150)


49. REMOVE FR DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C081788E01
  1. Using SST, remove the front differential case rear tapered roller bearing (outer race) and plate washer from the transmission case.

    SST
    09612-65014   (09612-01040, 09612-01050)

  1. C082144E01
    Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)


50. REMOVE TRANSMISSION CASE OIL SEAL

C081789E01
  1. Using SST and a hammer, drive out the transmission case oil seal from the manual transmission case.

    SST
    09950-60010   (09951-00530)
    09950-70010   (09951-07150)


51. REMOVE SHIFT AND SELECT LEVER SHAFT OIL SEAL

C121110
  1. Using a screwdriver and hammer, remove the shift and select lever shaft oil seal.


52. REMOVE SHIFT AND SELECT LEVER SHAFT SLIDE BALL BEARING

C121111E01
  1. Using SST and a hammer, remove the shift and select lever shaft slide ball bearing.

    SST
    09950-60010   (09951-00220)
    09950-70010   (09951-07200)

← COMPONENTS (from Nov 2006)INSPECTION (from Nov 2006) →