2005-2008 Yaris · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2006


1. INSTALL OUTPUT SHAFT COVER

C095191E01
  1. Coat the output shaft cover with MP grease and install it onto the front transaxle case.

    NOTICE:
    Insert the output shaft cover projection into the case side hollow.


2. INSTALL OUTPUT SHAFT FRONT BEARING

C080376E01
  1. Coat a new output shaft front bearing with gear oil. Using SST and a press, install it onto the front transaxle case.

    SST
    09950-60010   (09951-00550)
    09950-70010   (09951-07150)

    NOTICE:
    Install the new bearing in the correct direction, as shown in the illustration.


3. INSTALL FRONT TRANSAXLE CASE OIL SEAL

C081790E01
  1. Using SST and a hammer, install a new front transaxle case oil seal onto the front transalxe case.

    SST
    09950-60010   (09951-00370)
    09950-70010   (09951-07150)

    Drive in depth:
    15.6 to 16.0 mm (0.6141 to 0.6299 in.)

  1. Coat the lip of the front transaxle case oil seal with MP grease.


4. INSTALL INPUT SHAFT FRONT BEARING

C081791E01
  1. Coat a new input shaft front bearing with gear oil, and using SST and a press, install it onto the front transaxle case.

    SST
    09950-60010   (09951-00420)
    09950-70010   (09951-07150)

    Drive in depth:
    0 to 0.3 mm (0 to 0.0118 in.)


5. INSTALL SHIFT AND SELECT LEVER SHAFT SLIDE BALL BEARING

C121112E01
  1. Using SST and a hammer, install a new shift and select lever shaft slide ball bearing onto the transmission case.

    SST
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)

    Drive in depth:
    0 to 0.5 mm (0 to 0.0020 in.)


6. INSTALL SHIFT AND SELECT LEVER SHAFT OIL SEAL

C120752E01
  1. Using SST, install a new shift and select lever shaft oil seal onto the transmission case.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00240)

    Drive in depth:
    9.7 to 10.3 mm (0.382 to 0.406 in.)


7. INSTALL FR DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

C082146E01
  1. Using SST and a press, install the front differential case front tapered roller bearing (inner race) onto the front differential case.

    SST
    09350-32014   (09351-32120)
    09950-60010   (09951-00530)

  1. C080379E01
    Using SST and a press, install the front differential case front tapered roller bearing (outer race) together with the plate washer onto the front transaxle case.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)


8. INSTALL FR DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C082147E01
  1. Using SST and a press, install the front differential case rear tapered roller bearing (inner race) onto the differential case.

    SST
    09350-32014   (09351-32120)
    09950-60010   (09951-00530)

  1. C081792E01
    Using SST and a press, install the front differential case rear tapered roller bearing (outer race) with plate washer onto the transmission case.
    SST
    09309-36010  
    09950-60020   (09951-00710)
    09950-70010   (09951-07150)

    HINT:
    Use a plate washer of the same thickness as the removed one.


9. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

C067656
  1. Coat the differential case assembly with gear oil, and install it onto the front transaxle case.

  1. Install the manual transmission case with the 16 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. C081793E01
    Using SST and a torque wrench, turn the differential case assembly to the right and left 2 or 3 times to allow the bearings to settle.
    SST
    09564-32011  

  1. C081793E01
    Using SST and a torque wrench, measure the preload.
    SST
    09564-32011  

    Preload (at starting):
    New bearing:
    0.78 to 1.57 N*m (7.95 to 16.0 kgf*cm, 6.9 to 13.89 in.*lbf)
    Used bearing:
    0.49 to 0.98 N*m (5.0 to 10.0 kgf*cm, 4.34 to 8.67 in.*lbf)

    If the preload is outside the specifications, select another plate washer.

    Plate washer thickness:
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    AA
    2.10 (0.0827)
    LL
    2.60 (0.1024)
    BB
    2.15 (0.0846)
    MM
    2.65 (0.1043)
    CC
    2.20 (0.0866)
    NN
    2.70 (0.1063)
    DD
    2.25 (0.0886)
    PP
    2.75 (0.1083)
    EE
    2.30 (0.0906)
    QQ
    2.80 (0.1102)
    FF
    2.35 (0.0925)
    RR
    2.85 (0.1122)
    GG
    2.40 (0.0945)
    SS
    2.90 (0.1142)
    HH
    2.45 (0.0965)
    TT
    2.95 (0.1161)
    JJ
    2.50 (0.0984)
    UU
    3.00 (0.1181)
    KK
    2.55 (0.1004)
    -
    -

    HINT:
    The preload changes by approximately 0.3 to 0.4 N*m (3 to 4 kgf*cm, 2.6 to 3.5 in.*lbf) per each 0.05 mm (0.0020 in.) change in plate washer thickness.

  1. Remove the 16 bolts and the manual transmission case.

  1. Remove the differential case assembly from the front transaxle case.


10. INSTALL TRANSMISSION CASE OIL SEAL

C080381E01
  1. Using SST and a hammer, install a new transmission case oil seal onto the manual transmission case.

    SST
    09316-60011   (09316-00011)

    Drive in depth:
    9.6 to 10.2 mm (0.378 to 0.402 in.)

  1. Coat the lip of the front transmission case oil seal with MP grease.


11. INSTALL TRANSAXLE CASE OIL SEAL

C080382E01
  1. Using SST and a hammer, install a new transaxle case oil seal onto the front transaxle case.

    Drive in depth:
    1.6 to 2.2 mm (0.063 to 0.087 in.)

    SST
    09710-20011   (09710-06071)
    09950-70010   (09951-07150)

  1. Coat the lip of the transaxle case oil seal with MP grease.


12. INSTALL TRANSMISSION MAGNET

C067659E09
  1. Clean the transmission magnet and install it onto the front transaxle case.


13. INSTALL BEARING LOCK PLATE

C067658
  1. Install the bearing lock plate onto the front transaxle case with the bolt.

    Torque:
    11 N*m{ 115 kgf*cm , 8.3 ft.*lbf }


14. INSTALL NO. 1 OIL RECEIVER PIPE

C068380
  1. Install the No. 1 oil receiver pipe onto the manual transmission case with the bolt.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Do not deform the No. 1 oil receiver pipe.
    2. Install the No. 1 oil receiver pipe while holding it against the manual transmission case, as shown in the illustration.


15. INSTALL NO. 2 OIL RECEIVER PIPE

C080432
  1. Install the No. 2 oil receiver pipe onto the manual transmission case with the bolt.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Do not deform the No. 2 oil receiver pipe.
    2. Install the No. 2 oil receiver pipe while holding it against the manual transmission case, as shown in the illustration.


16. INSTALL REVERSE RESTRICT PIN ASSEMBLY

C080383
  1. Install the reverse restrict pin assembly onto the manual transmission case.

    NOTICE:
    Set the reverse restrict pin assembly in the correct orientation.

  1. C080384
    Using a pin punch (φ5 mm) and a hammer, install the slotted pin onto the reverse restrict pin assembly.

    Drive in depth:
    15.5 to 16.5 mm (0.6102 to 0.6496 in.)

  1. C120732
    Apply sealant to the reverse restrict pin plug.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a hexagon wrench and a torque wrench, install the reverse restrict pin plug onto the manual transmission case.

    Torque:
    13 N*m{ 130 kgf*cm , 9.3 ft.*lbf }


17. INSTALL MANUAL TRANSAXLE CASE RECEIVER

C067657
  1. Install the manual transaxle case receiver onto the front transaxle case with the bolt.

    Torque:
    11 N*m{ 115 kgf*cm , 8.3 ft.*lbf }


18. INSTALL DIFFERENTIAL CASE ASSEMBLY

C067656
  1. Coat the differential case tapered roller bearing with gear oil and install the differential case assembly onto the front transaxle case.


19. INSTALL INPUT SHAFT ASSEMBLY

C080586
  1. Coat the sliding and rotating surfaces of the input and output shafts with gear oil and install them onto the transaxle case.


20. INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

C080386E03
  1. Coat the reverse idler gear sub-assembly, thrust washer and reverse idler gear shaft with gear oil and install them as shown in the illustration.

    HINT:
    Align the mark on the reverse idler gear shaft with the bolt hole as shown in the illustration.


21. INSTALL NO. 1 GEAR SHIFT FORK SHAFT

C080387E04
  1. Coat the No. 1 gear shift fork and No. 2 gear shift fork with gear oil and install them.

  1. C080388E04
    Coat the No. 1 gear shift fork shaft with gear oil and install it.

  1. Apply sealant to the shift fork set bolt.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the shift fork set bolt.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }

  1. C080389
    Using a brass bar and a hammer, install a new shaft snap ring onto the No. 1 gear shift fork shaft.


22. INSTALL NO. 3 GEAR SHIFT FORK SHAFT

C080450
  1. Coat the 2 shift fork balls with MP grease and install them onto the reverse shift fork.

  1. Install the reverse shift fork onto the No. 3 gear shift fork shaft.

  1. C080391
    Using a brass bar and a hammer, install 2 new shift fork shaft snap rings onto the No. 3 shift fork shaft.

  1. C080392
    Coat the No. 3 gear shift fork shaft with gear oil and install it.


23. INSTALL NO. 2 GEAR SHIFT FORK SHAFT

C117123
  1. Coat the No. 1 gear shift head and No. 2 gear shift fork shaft with gear oil and install them.

    NOTICE:
    To avoid interference by the 2 shift fork balls, lift up the No. 3 gear shift fork shaft to the position shown in the illustration.

  1. C080361
    Coat the 2 shift lock bolts with sealant and install them onto No. 2 gear shift fork and No. 1 shift head.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


24. INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

C080360
  1. Install the reverse shift arm bracket assembly onto the front transaxle case with the 2 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }


25. INSTALL MANUAL TRANSMISSION CASE

C082142E01
  1. Apply FIPG to the manual transmission case, as shown in the illustration.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Assemble the parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

  1. C080358
    Install the 13 bolts onto the manual transmission side.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. C080357
    Install the 3 bolts onto the manual transaxle side.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


26. INSTALL REVERSE IDLER GEAR SHAFT BOLT

C067639
  1. Coat the reverse idler gear shaft bolt with sealant and install it with a new gasket.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


27. INSTALL NO. 2 LOCK BALL ASSEMBLY

C080356
  1. Coat the No. 2 lock ball assembly with sealant and install it with a hexagon wrench.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


28. INSTALL SHIFT DETENT BALL

D032759
  1. Install the 2 shift detent balls, 2 shift detent ball springs and 2 No. 1 shift detent ball spring seats onto the manual transmission case.

  1. C067634
    Coat the 2 shift detent ball plugs with sealant and install them using a hexagon wrench.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }

  1. C080393
    Install the shift detent ball, shift detent ball compression spring and No. 1 shift detent ball spring seat onto the front transaxle case.

  1. C080354
    Coat the shift detent ball plug with sealant and install it using a hexagon wrench.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


29. INSTALL INPUT SHAFT REAR BEARING HOLE SNAP RING

C080352
  1. Using a snap ring expander, install the new input shaft rear bearing hole snap ring onto the input shaft.


30. INSTALL OUTPUT SHAFT REAR BEARING HOLE SNAP RING

C080351
  1. Using a snap ring expander, install the new output shaft rear bearing hole snap ring onto the output shaft.


31. INSTALL SHIFT FORK SHAFT SHAFT SNAP RING

C080394
  1. Using a brass bar and a hammer, install a new shift fork shaft shaft snap ring onto the No. 2 shift fork shaft.


32. INSTALL BEARING RETAINER REAR

C080350
  1. Coat the 5 bolts with sealant, and install the bearing retainer rear onto the manual transmission case with the 5 bolts.

    Torque:
    27 N*m{ 280 kgf*cm , 20 ft.*lbf }


33. INSTALL 5TH DRIVEN GEAR

C095786E03
  1. Using SST, install the 5th driven gear onto the output shaft.

    SST
    09309-12020  


34. INSTALL 5TH GEAR NEEDLE ROLLER BEARING

C080348
  1. Coat the 5th gear needle roller bearing and 5th gear bearing spacer with gear oil, and install them onto the input shaft.


35. INSTALL 5TH GEAR

C080396
  1. Coat the 5th gear with gear oil and install it onto the input shaft.


36. INSTALL NO. 3 SYNCHRONIZER RING

D031112
  1. Coat the No. 3 synchronizer ring with gear oil and install it onto the 5th gear.


37. INSTALL NO. 3 TRANSMISSION CLUTCH HUB

C080398E01
  1. Install the 3 synchromesh shifting keys and 2 synchromesh shifting key springs onto the No. 3 transmission clutch hub, as shown in the illustration.

    NOTICE:
    Do not set the 2 shifting key spring openings in the same position.

  1. C080399E02
    Using SST and a hammer, install the No. 3 transmission clutch hub onto the input shaft.
    SST
    09636-20010  

    NOTICE:
    1. Do not install the No. 3 transmission clutch hub in the wrong direction.
    2. Install the No. 3 transmission clutch hub with the No. 3 synchronizer ring key groove and No. 3 synchromesh shifting key aligned.
    3. Check that the 5th gear is rotating.
    4. Place a suitable sized wooden block to support the input shaft.

  1. C080400
    Select a clutch hub No. 3 shaft snap ring that will allow minimum axial play.

    Clearance:
    0.1 mm or less

    Snap ring thickness:
    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    A
    2.25 (0.0886)
    E
    2.49 (0.0980)
    B
    2.31 (0.0909)
    F
    2.55 (0.1004)
    C
    2.37 (0.0933)
    G
    2.61 (0.1028)
    D
    2.43 (0.0957)
    -
    -

  1. Using a brass bar and a hammer, install the new snap ring onto the input shaft.


38. INSPECT 5TH GEAR THRUST CLEARANCE

C080344
  1. Using a dial indicator, measure the 5th gear thrust clearance.

    Standard clearance:
    0.1 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, the 5th gear or input shaft rear radial ball bearing.


39. INSPECT 5TH GEAR RADIAL CLEARANCE

C080345
  1. Using a dial indicator, measure the 5th gear radial clearance.

    Standard clearance:
    KOYO made:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.


40. INSTALL NO. 3 GEAR SHIFT FORK

C080401
  1. Coat the No. 3 transmission clutch hub sleeve with gear oil and install it together with the No. 3 gear shift fork onto No. 3 transmission clutch hub.

    HINT:
    Set the No. 3 transmission clutch hub in the correct orientation.

  1. C080402
    Coat the gear shift fork lock bolt with sealant, and install it onto the No. 3 gear shift fork.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


41. INSTALL MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

C080403
  1. Engage the 2 gears simultaneously to lock the transmission.

  1. Coat a new manual transmission output shaft rear set nut with sealant.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the new manual transmission output shaft rear set nut.

    Torque:
    118 N*m{ 1,200 kgf*cm , 87 ft.*lbf }

  1. C080404
    Using a chisel and a hammer, stake the manual transmission output shaft rear set nut.

  1. Disengage the 2 gears.


42. INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

C080556E02
  1. Apply FIPG to the manual transaxle case cover sub-assembly as shown in the illustration.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Assemble the parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

  1. C080554
    Install the manual transmission case cover sub-assembly onto the manual transmission case with the 9 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


43. INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

C120740
  1. Coat the shift and select lever shaft assembly with gear oil, and install it onto the transmission case.


44. INSTALL CONTROL SHAFT COVER OIL SEAL

C120731E01
  1. Using SST and a hammer, install a new control shaft cover oil seal onto the control shaft cover.

    Drive in depth:
    0.2 to 1.2 mm (0.0079 to 0.0472 in.)

    SST
    09950-60010   (09951-00280)
    09950-70010   (09951-07150)

  1. Coat the control shaft cover oil seal with MP grease.


45. INSTALL CONTROL SHAFT COVER

C120742
  1. Coat the 4 bolts with sealant. Install a new gasket and control shaft cover onto the manual transmission case with the 4 bolts.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Set the claws of the shift interlock plate into the shift head part of the gear shift fork shaft securely.


46. INSTALL SHIFT GATE PIN

C120743
  1. Coat the shift gate pin with sealant.

  1. Install the washer and shift gate pin.

    Torque:
    11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


47. INSTALL NO. 1 LOCK BALL ASSEMBLY

C120744
  1. Coat the No. 1 lock ball assembly with sealant and install it onto the manual transmission case.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


48. INSTALL SHIFT LEVER DAMPER

C120746
  1. Install the dust boot onto the control shaft cover.

  1. Install the shift lever damper with the lock pin onto the shift and select lever shaft assembly.

  1. Install the spring washer with the nut.

    Torque:
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf }


49. INSTALL FLOOR SHIFT CONTROL SHIFT LEVER

C120748
  1. Install the dust boot onto the shift and select lever shaft oil seal.

  1. Install the floor shift control shift lever with the lock pin onto the shift and select lever shaft assembly.

  1. Install the spring washer with the nut.

    Torque:
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf }


50. INSTALL SELECTING BELL CRANK ASSEMBLY

C120750
  1. Install the selecting bell crank assembly together with the control shift lever bush onto the manual transmission case with the 2 bolts and nut.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf } for bolt
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf } for nut

    NOTICE:
    Apply MP grease to the inside circumferential surface of the control shift lever bush.


51. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

C120749E01
  1. Using SST, install the back-up light switch assembly onto the manual transmission case with a new gasket.

    SST
    09817-16011  

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }

  1. Install the back-up light switch wire harness into the 2 clamps.


52. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Install a new O-ring onto the speedometer driven hole cover sub-assembly.

  1. Install the speedometer driven hole cover sub-assembly onto the manual transaxle case with the bolt.

    Torque:
    11 N*m{ 115 kgf*cm , 8.3 ft.*lbf }


53. INSTALL MANUAL TRANSMISSION FILLER PLUG

C080549
  1. Install the manual transmission filler plug onto the manual transmission case with a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


54. INSTALL DRAIN PLUG SUB-ASSEMBLY

C080550
  1. Install the drain plug onto the manual transmission case with a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

← INSPECTION (from Nov 2006)COMPONENTS (from Nov 2006) →