2005-2008 Yaris · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

C107511
  1. Provisionally tighten a new nut through the No. 2 suspension support.

  1. Install the front shock absorber with coil spring onto the steering knuckle.

  1. C125277
    Install the 2 bolts and 2 nuts.

    Torque:
    164 N*m{ 1,672 kgf*cm , 121 ft.*lbf }

    HINT:
    Keep the bolt from rotating while loosening and removing the nuts.


2. INSTALL FRONT FLEXIBLE HOSE

C125274
  1. Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.


3. INSTALL FRONT STABILIZER LINK ASSEMBLY

C125276
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


4. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


5. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

C107504
  1. Using a socket hexagon wrench 6, fix the shock absorber rod and tighten the nut.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }


6. INSTALL FRONT SUSPENSION SUPPORT DUST COVER

7. INSTALL COWL TOP PANEL OUTER
  1. Install the cowl top panel outer with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the clamp and install the wiper motor connector wire harness.


8. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A118801E01
  1. Engage the claws, and install cowl to register duct No. 2.


9. INSTALL FRONT WIPER MOTOR AND LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


10. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


11. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


12. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


13. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


14. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


17. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)
← REASSEMBLY (from Nov 2005)DISPOSAL (from Nov 2005) →