BLEEDING
Removal / installation · Vehicles built from Nov 2005
- NOTICE:
- Immediately wash off any brake fluid that comes into contact with any painted surfaces.
- HINT:
- If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.
| 1. FILL RESERVOIR WITH BRAKE FLUID |
![]() ![]() |
Remove the cowl top ventilator louver.
Set the brake fluid can upside down on the reservoir.

- Fluid:
- SAE J1704 or FMVSS No. 116 DOT4
| 2. BLEED MASTER CYLINDER |
- HINT:
- If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.
w/o VSC:

Using SST, disconnect the brake tubes from the master cylinder.
- SST
- 09023-00100
w/ VSC:
Using SST, disconnect the brake tubes from the master cylinder.
- SST
- 09023-38200
Slowly depress the brake pedal and hold it there (Step A).

Block the outer holes with your fingers, and release the brake pedal (Step B).

Repeat steps A and B 3 or 4 times.
w/o VSC:

Using SST, connect the brake tubes to the master cylinder.
- SST
- 09023-00100
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
w/ VSC:
Using SST, connect the brake tubes to the master cylinder.
- SST
- 09023-38200
- Torque:
- for use without SST:
- 20 N*m{ 199 kgf*cm , 14 ft.*lbf }
- for use with SST:
- 18 N*m{ 180 kgf*cm , 13 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
| 3. BLEED BRAKE LINE |
![]() ![]() |
Connect the vinyl tube to the bleeder plug.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).
At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).
Repeat steps C and D until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Disc Brake:
- 17 N*m{ 173 kgf*cm , 13 ft.*lbf }
- Rear Drum Brake:
- 9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
- Rear Disc Brake:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
Repeat the above procedure to bleed the air out of the brake line for each wheel.
| 4. BLEED BRAKE ACTUATOR (w/ VSC) |
- NOTICE:
- After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.
Depress the brake pedal more than 20 times with the engine off.
Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).

- NOTICE:
- Do not start the engine.
Select AIR BLEEDING on the intelligent tester.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Bleed the air out of the brake line when Step 1: Increase appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty of brake fluid.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).
Repeat steps E and F until all air in the fluid is completely bled out.
Tighten the bleeder plug completely.
- Torque:
- Front Disc Brake:
- 17 N*m{ 173 kgf*cm , 13 ft.*lbf }
- Rear Drum Brake:
- 9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
- Rear Disc Brake:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
Repeat the above procedure for each wheel to bleed the air out of the brake line.
Bleed the air out of the suction line when Step 2: Inhalation appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty of brake fluid.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.
Operate the brake actuator to bleed the air using the intelligent tester (Step G).
- NOTICE:
- Release the brake pedal at this time.
- HINT:
- This operation stops automatically after 4 seconds.
Check if the operation has stopped by referring to the intelligent tester display (Step H).
Repeat steps G and H until all air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Disc Brake:
- 17 N*m{ 173 kgf*cm , 13 ft.*lbf }
- Rear Drum Brake:
- 9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
- Rear Disc Brake:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty of brake fluid.
- Bleed the air by following the steps displayed on the the intelligent tester.
Connect the vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug (Step I).
Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there.
- NOTICE:
- During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
- Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.
- During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
- HINT:
- The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
- When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.
- The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
Tighten the bleeder plug, then release the brake pedal (Step J).
Repeat steps I and J until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Disc Brake:
- 17 N*m{ 173 kgf*cm , 13 ft.*lbf }
- Rear Drum Brake:
- 9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
- Rear Disc Brake:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty of brake fluid.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step K).

When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step L).
Repeat steps K and L until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Disc Brake:
- 17 N*m{ 173 kgf*cm , 13 ft.*lbf }
- Rear Drum Brake:
- 9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
- Rear Disc Brake:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Make sure that the air bleeding is complete by referring to the intelligent tester display.
| 5. CHECK FLUID LEVEL IN RESERVOIR |
Check the fluid level and add fluid if necessary.
- Fluid:
- SAE J1704 or FMVSS No. 116 DOT4

