2005-2008 Yaris · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built Aug 2005 – Dec 2005

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the 4 bolts and remove the hood.


3. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


8. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


10. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


11. REMOVE FRONT WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


12. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A118801E01
  1. Disengage the claws, and remove the cowl to resister duct No. 2.


13. REMOVE COWL TOP PANEL OUTER

A116498
  1. Disengage the clamp, and separate the wiper motor connector.

  1. A116497
    Remove the 9 bolts and the cowl top panel outer.


14. POSITION WHEELS FACING STRAIGHT AHEAD

15. REMOVE FRONT WHEEL

16. REMOVE COLUMN HOLE COVER SILENCER SHEET

  1. A116501
    Remove the floor carpet and 2 clips and remove the column hole cover silencer.


17. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

  1. C117212
    Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.

  1. C118005E03
    Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the power steering.

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.


18. REMOVE STEERING COLUMN NO. 1 HOLE COVER SUB-ASSEMBLY

  1. C118001E01
    Remove clip A, separate clip B from the body and separate steering column hole cover No. 1.

    NOTICE:
    Do not damage clip B.


19. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C116895E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.


20. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


21. SEPARATE FRONT SUSPENSION LOWER ARM LH

C107513
  1. Remove the clip and castle nut.

  1. C107514E01
    Using SST, separate the lower arm.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.


22. SEPARATE FRONT SUSPENSION LOWER ARM RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


23. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


24. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


25. SUSPEND ENGINE ASSEMBLY

  1. 1KR-FE

    1. Remove the bolt and remove the wire harness clamp bracket.

    2. C108065
      Install the engine hanger with the bolt in the position shown in the illustration.

      Part No.:
      No. 1 engine hanger :
      12281-40030
      No. 2 engine hanger:
      12282-40010
      Bolt:
      91671-80820

      Torque:
      28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    3. Using an engine sling device and a chain block, support the engine assembly.

  1. 1NZ-FE, 2NZ-FE

    1. Remove the bolt and remove the radio setting condenser.

    2. Remove the bolt and remove the air-fuel ratio sensor wiring bracket.

    3. A070012E01
      Install the engine hanger with the bolt in the position shown in the illustration.

      Part No.:
      Engine hanger :
      12281-21010
      Bolt:
      91642-81025

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    4. Using an engine sling device and a chain block, support the engine assembly w/transaxle and front suspension crossmember.


26. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

  1. C107979
    Remove the bolt and separate the engine moving control rod.

  1. Support the front suspension crossmember with a transmission jack.

  1. C107982
    Remove the 6 bolts and remove the suspension crossmember.


27. REMOVE FRONT SUSPENSION LOWER ARM RH

C112612
  1. Remove the bolt and lower arm.

← COMPONENTS (from Jan 2006)REMOVAL (from Jan 2006) →