INSTALLATION
Removal / installation · Vehicles built from Aug 2005
| 1. INSTALL FRONT STABILIZER BAR NO. 1 BUSH |
![]() ![]() |
Install the stabilizer bar bush onto the stabilizer bar.
- HINT:
- Install the bush onto the stabilizer so that the bush stopper of the stabilizer bar faces the outside of the vehicle.
- Install the bush with its cutout facing the front of the vehicle.
- Install the bush onto the stabilizer so that the bush stopper of the stabilizer bar faces the outside of the vehicle.
| 2. INSTALL FRONT STABILIZER BAR |
![]() ![]() |
Install the stabilizer onto the crossmember with the paint mark on the left side of the vehicle.
| 3. INSTALL FRONT STABILIZER NO. 1 BRACKET LH |
![]() ![]() |
Provisionally tighten bolt A.
Tighten the bolts to the specified torque, in the order of B then A.
- Torque:
- 47 N*m{ 479 kgf*cm , 35 ft.*lbf }
| 4. INSTALL FRONT STABILIZER NO. 1 BRACKET RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 5. INSTALL POWER STEERING GEAR |
![]() ![]() |
Install the power steering gear onto the front suspension crossmember with the 2 bolts and 2 nuts.
- Torque:
- 96 N*m{ 979 kgf*cm , 71 ft.*lbf }
- NOTICE:
- Keep the nut from rotating while turning the bolt.
| 6. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
Support the front suspension crossmember with a transmission jack.
Provisionally install the front suspension crossmember onto the body with the 6 bolts.

Bolt
Underhead Length (mm)
A
38
B
99
C
41
By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.
- SST
- 09670-00011
- Torque:
- 70 N*m{ 714 kgf*cm , 52 ft.*lbf } for Bolt A
- 160 N*m{ 1,631 kgf*cm , 118 ft.*lbf } for Bolt B
- 95 N*m{ 969 kgf*cm , 70 ft.*lbf } for Bolt C
- NOTICE:
- Insert SST into the datum hole in a vertical orientation.
- If SST can not be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.
- Insert SST into the datum hole in a vertical orientation.


Install the engine moving control rod with the bolt.

- Torque:
- 120 N*m{ 1,224 kgf*cm , 89 ft.*lbf }
| 7. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
![]() ![]() |
Install the stabilizer link with the 2 nuts.
- Torque:
- 74 N*m{ 755 kgf*cm , 55 ft.*lbf }
- HINT:
- If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.
| 8. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 9. INSTALL FRONT SUSPENSION LOWER ARM LH |
![]() ![]() |
Install the lower arm onto the steering knuckle with a new castle nut.
- Torque:
- 98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }
- NOTICE:
- If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.
Install a new clip.
| 10. INSTALL FRONT SUSPENSION LOWER ARM RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 11. INSTALL TIE ROD END SUB-ASSEMBLY LH |
![]() ![]() |
Install the tie rod end onto the steering knuckle with a new castle nut.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
- NOTICE:
- If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.
Install a new cotter pin.
| 12. INSTALL TIE ROD END SUB-ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 13. INSTALL STEERING COLUMN NO. 1 HOLE COVER SUB-ASSEMBLY |
Install clip B onto the body portion and install column No. 1 onto the body portion with clip A.

- NOTICE:
- Make sure that the lip portion of hole cover No. 1 is not damaged.
| 14. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() ![]() |
Align the matchmarks and install the sliding yoke onto the intermediate shaft.
- Torque:
- 28 N*m{ 290 kgf*cm , 21 ft.*lbf }
Tighten bolt A.
- Torque:
- 28 N*m{ 290 kgf*cm , 21 ft.*lbf }
| 15. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() ![]() |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 16. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1KR-FE) |
![]() ![]() |
Using vernier calipers, measure the free length of the compression spring.
- Minimum length (Front Side):
- 40.5 mm (1.594 in.)
- Minimum length (Rear Side):
- 38.5 mm (1.516 in.)
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

- NOTICE:
- Install the exhaust pipe gasket in the correct direction.
- Do not damage the outer surface of the exhaust pipe gasket.
- Do not reuse the exhaust pipe gasket.
- Do not push in the gasket with the exhaust pipe when connecting it.
- Install the exhaust pipe gasket in the correct direction.
Install the 3 exhaust pipe support No. 4.
Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.


- Torque:
- 43 N*m{ 439 kgf*cm , 32 ft.*lbf }
| 17. INSTALL FRONT WHEEL |
- Torque:
- 103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }
| 18. POSITION WHEELS FACING STRAIGHT AHEAD |
| 19. INSTALL COWL TOP PANEL OUTER |
Install the cowl top panel outer with the 9 bolts.
- Torque:
- 6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
Engage the clamp and install the wiper motor connector wire harness.
| 20. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY |
![]() ![]() |
Engage the claws, and install the cowl to register duct No. 2.
| 21. INSTALL FRONT WIPER MOTOR AND LINK |
![]() ![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 22. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD) |
![]() ![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 23. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() ![]() |
Connect the washer hose.
Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

Install the clip.
Connect the washer hose.
Engage the 2 hooks and install cowl top ventilator louver center No. 1.

| 24. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD) |
![]() ![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 25. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() ![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 26. INSTALL HOOD TO COWL TOP SEAL |
![]() ![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 27. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 28. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 29. INSTALL FRONT WIPER ARM HEAD CAP |
![]() ![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 30. INSPECT HOOD SUB-ASSEMBLY |
Check that the clearance measurements are within the standard ranges.


- Standard:
Area
Measurement
Area
Measurement
A
1.7 to 5.7 mm
(0.067 to 0.224 in.)
G
-1.55 to 2.45 mm
(-0.061 to 0.096 in.)
B
-2 to 2 mm
(-0.079 to 0.079 in.)
H
1.75 to 5.75 mm
(0.067 to 0.226 in.)
C
4.45 to 10.45 mm
(0.175 to 0.411 in.)
I
-1.25 to 2.75 mm
(-0.049 to 0.108 in.)
D
-0.95 to 5.05 mm
(-0.037 to 0.199 in.)
J
-1.5 to 1.5 mm
(-0.059 to 0.059 in.)
E
7.55 to 13.55 mm
(0.297 to 0.533 in.)
K
2.0 to 5.0 mm
(0.079 to 0.197 in.)
F
1.65 to 5.65 mm
(0.065 to 0.222 in.)
-
-
| 31. ADJUST HOOD SUB-ASSEMBLY |
Loosen the hood side hinge bolts.

Move the hood to adjust the clearance to within the standard range.
Tighten the hood side hinge bolts after the adjustment.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
Adjust the height of the hood front end by turning the cushion rubber.

- HINT:
- The cushion rubber can be raised and lowered by turning it.
Adjust the hood lock.

Loosen the 3 bolts.
Adjust the hood lock position so that the striker can enter it smoothly.
Tighten the 3 bolts after the adjustment.
- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
| 32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 33. CHECK FOR EXHAUST GAS LEAKAGE (for 1KR-FE) |
| 34. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |



















