2005-2008 Yaris · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Jan 2006


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the 4 bolts and remove the hood.


3. REMOVE FRONT WIPER ARM HEAD CAP

  1. E127832E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E127833
    Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH

  1. E127834E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.


7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

  1. E127838
    Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.

  1. E127839
    Disconnect the washer hoses.

  1. Disengage the 5 hooks.


9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

  1. E127835
    Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.

  1. E127836
    Disconnect the washer hoses.

  1. Disengage the 5 hooks.


10. REMOVE FRONT WIPER MOTOR AND LINK

  1. E127837
    Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


11. REMOVE FRONT AIR SHUTTER SEAL

A133324
  1. Disengage the 3 claws and remove the front air shutter seal.


12. REMOVE COWL TOP PANEL OUTER

A128446
  1. Disengage the wire harness clamp.

  1. A128447
    Remove the 2 bolts and remove the cowl top to cowl inner brace.

  1. A128448
    Remove the 8 bolts and remove the cowl top panel outer.


13. POSITION WHEELS FACING STRAIGHT AHEAD

14. REMOVE FRONT WHEEL

15. REMOVE COLUMN HOLE COVER SILENCER SHEET

  1. A116501
    Remove the floor carpet and 2 clips and remove the column hole cover silencer.


16. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

  1. C139107
    Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.

  1. C118005E03
    Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the power steering.

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.


17. REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY

C125686E01
  1. Remove clip A, separate clip B from the body and separate No. 1 steering column hole cover.

    NOTICE:
    Do not damage clip B.


18. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C116895E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.


19. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


20. SEPARATE FRONT SUSPENSION LOWER ARM LH

C107513
  1. Remove the clip and castle nut.

  1. C107514E01
    Using SST, separate the lower arm.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.


21. SEPARATE FRONT SUSPENSION LOWER ARM RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


22. REMOVE FRONT STABILIZER LINK ASSEMBLY LH

C107518
  1. Remove the 2 nuts and stabilizer link

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


23. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


24. SUSPEND ENGINE ASSEMBLY

  1. 1NZ-FE, 2NZ-FE

    1. Remove the bolt and remove the radio setting condenser.

    2. Remove the bolt and remove the air-fuel ratio sensor wiring bracket.

    3. A070012E01
      Install the engine hanger with the bolt in the position shown in the illustration.

      Part No.:
      Engine hanger :
      12281-21010
      Bolt:
      91642-81025

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    4. Using an engine sling device and a chain block, support the engine assembly w/transaxle and front suspension crossmember.


25. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

  1. C107979
    Remove the bolt and separate the engine moving control rod.

  1. Support the front suspension crossmember with a transmission jack.

  1. C107982
    Remove the 6 bolts and remove the suspension crossmember.


26. REMOVE POWER STEERING GEAR

C117189
  1. Remove the 2 bolts and 2 nuts and remove the power steering gear from the suspension crossmember.

    NOTICE:
    Keep the nut from rotating while turning the bolt.


27. REMOVE FRONT STABILIZER BRACKET LH

C116871
  1. Remove the 2 bolts and the stabilizer bracket.


28. REMOVE FRONT STABILIZER BRACKET RH
  1. Remove the 2 bolts and the stabilizer bracket.


29. REMOVE FRONT STABILIZER BAR

30. REMOVE FRONT STABILIZER BAR BUSH
← COMPONENTS (from Jan 2006)INSPECTION (from Jan 2006) →