REMOVAL
Removal / installation · Vehicles built from Aug 2005
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE REAR WHEEL |
| 3. DRAIN BRAKE FLUID |
- NOTICE:
- Immediately wash off any brake fluid that comes into contact with any painted surfaces.
| 4. SEPARATE SKID CONTROL SENSOR WIRE |
![]() ![]() |
Using a screwdriver, remove the claw of the connector lock portion and disconnect the skid control sensor wire connector.
- NOTICE:
- Do not remove the connector cover from the connector because the skid control sensor wire may be damaged.
Remove the nut and separate the skid control sensor wire.

| 5. SEPARATE REAR BRAKE NO. 4 TUBE (for Rear Drum Brake) |
![]() ![]() |
Using SST, separate the brake tube from the flexible hose.
- SST
- 09023-00100
Remove the clip and disconnect the flexible hose from the axle beam.
Remove the nut and separate the brake tube.
| 6. SEPARATE REAR BRAKE NO. 3 TUBE (for Rear Drum Brake) |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 7. REMOVE REAR BRAKE NO. 4 TUBE (for Rear Disc Brake) |
![]() ![]() |
Using SST, separate the brake tube from the flexible hose.
- SST
- 09023-00100
Remove the 2 clips and disconnect the 2 flexible hoses from the axle beam.
Remove the nut and remove the brake tube.
| 8. REMOVE REAR BRAKE NO. 3 TUBE (for Rear Disc Brake) |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 9. SEPARATE PARKING BRAKE NO. 3 CABLE ASSEMBLY |
![]() ![]() |
Using pliers, pinch both ends of the claw of cable clamp and flex the clamp to remove it.
Remove the bolt and separate the parking brake cable.
| 10. SEPARATE PARKING BRAKE NO. 2 CABLE ASSEMBLY |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 11. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake) |
Release the parking brake and remove the rear brake drum.
If the rear brake drum cannot be removed easily, perform the following procedure.
Remove the hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjust lever away from the adjuster.

Using another screwdriver, contract the brake shoe by turning the adjusting bolt.
| 12. SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY LH (for Rear Disc Brake) |
![]() ![]() |
Remove the 2 bolts while holding the slide pin with a spanner and separate the disc brake cylinder.
- NOTICE:
- Suspend the disc brake cylinder with a piece of rope.
| 13. SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY RH (for Rear Disc Brake) |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 14. REMOVE REAR DISC BRAKE PAD KIT (PAD ONLY) (for Rear Disc Brake) |
![]() ![]() |
Remove the 2 disc brake pads from the disc brake cylinder mounting.
| 15. REMOVE REAR DISC BRAKE CYLINDER MOUNTING LH (for Rear Disc Brake) |
![]() ![]() |
Remove the 2 bolts and remove the disc brake cylinder mounting from the axle beam.
| 16. REMOVE REAR DISC BRAKE CYLINDER MOUNTING RH (for Rear Disc Brake) |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 17. REMOVE REAR DISC (for Rear Disc Brake) |
![]() ![]() |
Place matchmarks on the disc and axle hub and remove the disc.
| 18. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH |
![]() ![]() |
for Rear Drum Brake:
Remove the 4 bolts and remove the axle hub and bearing from the axle beam.
- NOTICE:
- Suspend the backing plate with a piece of rope.
for Rear Disc Brake:
Remove the 4 bolts and remove the axle hub and bearing and the dust cover from the axle beam.
| 19. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 20. LOOSEN REAR AXLE BEAM |
![]() ![]() |
Loosen the 2 bolts.
- NOTICE:
- Do not remove the bolts.
| 21. REMOVE REAR ABSORBER CAP |
| 22. REMOVE REAR ABSORBER CAP |
| 23. REMOVE REAR SHOCK ABSORBER CAP LH |
| 24. REMOVE REAR SHOCK ABSORBER CAP RH |
| 25. REMOVE REAR SHOCK ABSORBER LH |
Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.
Remove the 2 nuts while keeping the piston rod from rotating.

Remove the cushion retainer and suspension support.
Remove the bolt while keeping the nut from rotating and remove the shock absorber.

- NOTICE:
- Remove the nut fromthe bolt side because the one on the lower side is a jam nut.
| 26. REMOVE REAR SHOCK ABSORBER RH |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 27. REMOVE REAR COIL SPRING LH |
Lower the jacks slowly.
Remove the coil spring, coil spring insulator upper and coil spring insulator lower.
| 28. REMOVE REAR COIL SPRING RH |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 29. REMOVE REAR AXLE BEAM |
![]() ![]() |
Remove the 2 bolts and remove the axle beam.










