2005-2008 Yaris · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Jan 2006


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

  1. B138595
    Hold the front edge of the rear seat cushion cover pad and lift it up, as shown in the illustration, to disengage the 2 hooks.

    NOTICE:
    Hold the area around the hooks so as to avoid deforming the rear seat cushion frame.

  1. Pass the rear seat inner belt through the slit in the rear seat cushion cover pad, disengage the hook between the rear seat cushion cover pad and the rear seatback, and remove the rear seat cushion cover pad.


3. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B138450E01
    Remove the rear seat outer belt from the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Remove the rear center seat outer belt from the rear center seat shoulder belt guide.

  1. B134981
    Remove the 3 bolts.

  1. Disengage the 3 hooks and remove the rear seatback.


4. REMOVE REAR WHEEL

5. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.


6. SEPARATE SKID CONTROL SENSOR WIRE (w/ ABS)

C125279
  1. Using a screwdriver, remove the claw of the connector lock portion and disconnect the skid control sensor wire connector.

    NOTICE:
    Do not remove the connector cover from the connector because the skid control sensor wire may be damaged.

  1. C107566
    Remove the nut and separate the skid control sensor wire.


7. SEPARATE REAR NO. 4 BRAKE TUBE

C107570E01
  1. Using SST, separate the brake tube from the flexible hose.

    SST
    09023-00100  

  1. Remove the clip and disconnect the flexible hose from the axle beam.

  1. Remove the nut and separate the brake tube.


8. SEPARATE REAR NO. 3 BRAKE TUBE

HINT:
The removal procedure for the RH side is the same as that for the LH side.


9. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

C126196
  1. Using pliers, pinch both ends of the claw of cable clamp and flex the clamp to remove it.

  1. Remove the bolt and separate the parking brake cable.

  1. Remove the cable clamp from the parking brake cable.

    HINT:
    Replace the clamp with a new one when installing the parking brake cable.


10. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
The removal procedure for the RH side is the same as that for the LH side.


11. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY
  1. Release the parking brake and remove the rear brake drum.
    If the rear brake drum cannot be removed easily, perform the following procedure.

  1. F046068E02
    Remove the hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjust lever away from the adjuster.

  1. Using another screwdriver, contract the brake shoe by turning the adjusting bolt.


12. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

C121821
  1. Remove the 4 bolts and remove the axle hub and bearing from the axle beam.

    NOTICE:
    Suspend the backing plate with a piece of rope.


13. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


14. LOOSEN REAR AXLE BEAM

C112605E01
  1. Loosen the 2 bolts.

    NOTICE:
    Do not remove the bolts.


15. REMOVE REAR SHOCK ABSORBER CAP LH

16. REMOVE REAR SHOCK ABSORBER CAP RH

17. REMOVE REAR SHOCK ABSORBER LH
  1. Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.

  1. C132100
    Remove the 2 nuts while keeping the piston rod from rotating.

  1. Remove the cushion retainer and suspension support.

  1. C106031
    Remove the bolt while keeping the nut from rotating and remove the shock absorber.

    NOTICE:
    Remove the nut fromthe bolt side because the one on the lower side is a jam nut.


18. REMOVE REAR SHOCK ABSORBER RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


19. REMOVE REAR COIL SPRING LH
  1. Lower the jacks slowly.

  1. Remove the coil spring, coil spring insulator upper and coil spring insulator lower.


20. REMOVE REAR COIL SPRING RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


21. REMOVE REAR AXLE BEAM

C112605E01
  1. Remove the 2 bolts and remove the axle beam.

← COMPONENTS (from Jan 2006)REPLACEMENT (from Jan 2006) →