INSTALLATION
Removal / installation · Vehicles built from Aug 2005
| 1. INSTALL TRANSMISSION CASE OIL SEAL |
![]() ![]() |
Coat the lip of a new oil seal with MP grease.
Using SST and a hammer, install the new oil seal.
- SST
- 09309-37010
- Drive in depth:
- 9.6 to 10.2 mm (0.378 to 0.402 in.)
- NOTICE:
- Do not damage the oil seal lip.
| 2. INSTALL TRANSAXLE CASE OIL SEAL |
![]() ![]() |
Coat the lip of a new oil seal with MP grease.
Using SST and a hammer, install the new oil seal.
- SST
- 09710-26011
(09710-05061)
- Drive in depth:
- 1.6 to 2.2 mm (0.063 to 0.087 in.)
- NOTICE:
- Do not damage the oil seal lip.
| 3. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
for Automatic Transaxle:
Coat the spline of the inboard joint with ATF.
for Manual Transaxle:
Coat the spline of the inboard joint with gear oil.
Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.

- NOTICE:
- Face the cut area of the front drive inboard joint hole snap ring downward.
- Do not damage the oil seal.
- Do not damage the inboard joint boot.
- Face the cut area of the front drive inboard joint hole snap ring downward.
- HINT:
- Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.
| 4. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 5. INSTALL FRONT AXLE ASSEMBLY LH |
Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.
- NOTICE:
- Do not push the front axle further out of the vehicle than is necessary.
- Do not damage the outboard joint boot.
- Check for any foreign matter on the speed sensor rotor and insertion part.
- Do not damage the speed sensor rotor.
- Do not push the front axle further out of the vehicle than is necessary.
| 6. INSTALL FRONT AXLE ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 7. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
![]() ![]() |
Install the stabilizer link with the nut.
- Torque:
- 74 N*m{ 755 kgf*cm , 55 ft.*lbf }
- HINT:
- If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.
| 8. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 9. INSTALL TIE ROD END SUB-ASSEMBLY LH |
![]() ![]() |
Install the tie rod end onto the steering knuckle with a new castle nut.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
- NOTICE:
- If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.
Install a new cotter pin.
| 10. INSTALL TIE ROD END SUB-ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 11. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH |
![]() ![]() |
Install the lower arm onto the steering knuckle with a new castle nut.
- Torque:
- 98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }
- NOTICE:
- If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.
Install a new clip.
| 12. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 13. INSTALL SPEED SENSOR FRONT LH |
![]() ![]() |
Install the speed sensor onto the steering knuckle with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
- NOTICE:
- Check that the speed sensor tip and installation portion are free of foreign matter.
- Install the speed sensor without turning it from its original installation angle.
- Check that the speed sensor tip and installation portion are free of foreign matter.
Install the flexible hose and speed sensor with the bolt.

- Torque:
- 29 N*m{ 300 kgf*cm , 22 ft.*lbf }
- NOTICE:
- Install the flexible hose and speed sensor without twisting them.
| 14. INSTALL SPEED SENSOR FRONT RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 15. INSTALL FRONT AXLE SHAFT LH NUT |
![]() ![]() |
Using a 30 mm socket wrench, install a new axle hub nut.
- Torque:
- 216 N*m{ 2,203 kgf*cm , 160 ft.*lbf }
Using a chisel and hammer, caulk the axle hub nut.
| 16. INSTALL FRONT AXLE SHAFT RH NUT |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 17. INSTALL FRONT WHEELS |
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 19. ADD TRANSAXLE OIL |
| 20. INSPECT AND ADJUST TRANSAXLE OIL |
![]() ![]() |
Stop the vehicle in a level place.
Remove the transmission filler plug and the gasket.
Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.
- NOTICE:
- Excessively large or small amounts of oil may cause problems.
- After replacing the oil, drive the vehicle and check the oil level again.
- Excessively large or small amounts of oil may cause problems.
Check for oil leakage when the oil level is low.
Install the transmission filler plug and a new gasket.
- Torque:
- 39 N*m{ 400 kgf*cm , 29 ft.*lbf }
| 21. INSPECT ABS SPEED SENSOR SIGNAL |
| 22. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 23. CHECK FOR TRANSAXLE OIL LEAKAGE |








