2005-2008 Yaris · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE COLUMN HOLE COVER SILENCER SHEET

  1. A116501
    Remove the floor carpet and 2 clips and remove the column hole cover silencer.


3. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

  1. C117212
    Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.

  1. C118005E03
    Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the power steering.

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.


4. REMOVE FRONT WHEELS

5. REMOVE ENGINE UNDER COVER

6. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


7. REMOVE HOOD SUB-ASSEMBLY

8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


10. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


11. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


12. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


14. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


15. REMOVE WINDSHIELD WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


16. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO.2

A118801E01
  1. Disengage the claws, and remove cowl top register duct No. 2.


17. REMOVE COWL TOP PANEL OUTER

A126332
  1. Separate the wire harness.

  1. Remove the 9 bolts and cowl top panel outer.


18. REMOVE ENGINE COVER SUB-ASSEMBLY NO. 1

  1. A125743
    Disengage the 4 pins and remove engine cover No. 1.


19. REMOVE AIR CLEANER HOSE NO.1

C127625
  1. Loosen the hose clamp and disconnect air cleaner hose No. 1.

  1. Disconnect the 2 fuel hoses.

  1. Loosen the 2 clips and disconnect air cleaner hose No. 1.


20. REMOVE AIR CLEANER ASSEMBLY

  1. A125745
    Remove the 3 bolts, then remove the air cleaner case with air the cleaner inlet.


21. REMOVE AIR CLEANER BRACKET

C127612
  1. Remove the 3 bolts and the air cleaner bracket.


22. REMOVE BATTERY HOLD DOWN CLAMP

23. REMOVE BATTERY

24. REMOVE BATTERY TRAY

25. REMOVE BATTERY CARRIER

C106370
  1. Remove the 5 bolts and the battery carrier.


26. REMOVE AIR HOSE NO.2

C127613
  1. Loosen the 2 hose clamps and remove air hose No. 2.


27. REMOVE AIR TUBE NO.1

C127619
  1. Loosen the hose clamp and disconnect air hose No. 1.

  1. Remove the bolt and separate the wire harness bracket.

  1. Remove the 2 bolts and remove air tube No. 1.


28. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

C115305
  1. Remove the 2 clips and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.


29. REMOVE CONTROL CABLE BRACKET

C106374
  1. Remove the 2 bolts and the control cable bracket.


30. DISCONNECT WIRE HARNESS

C108079
  1. Remove the bolt, then disconnect the wire harness.


31. DISCONNECT CONNECTOR
  1. Disconnect the back-up light switch connector.


32. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

C115310
  1. Remove the 2 bolts and the clutch release cylinder.


33. REMOVE CLUTCH ACCUMULATOR ASSEMBLY

  1. C127602
    Using SST, disconnect the release cylinder to accumulator tube.
    SST
    09023-00101  

  1. C127603
    Using SST, remove the accumulator to flexible hose tube.
    SST
    09023-00101  

  1. C127604
    Remove the bolt, then separate the flexible hose bracket.

  1. C127605
    Remove the 2 bolts and nut and remove the clutch accumulator.


34. REMOVE STARTER ASSEMBLY

A128345
  1. Remove the terminal cap.

  1. Separate the harness clamp.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. Remove the 2 bolts and remove the starter assembly.


35. REMOVE FRONT AXLE SHAFT LH NUT

C085629E01
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.


36. REMOVE FRONT AXLE SHAFT RH NUT

HINT:
The removal procedure for the RH side is the same as that for the LH side.


37. SEPARATE SPEED SENSOR FRONT LH

C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.

  1. C112274
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.


38. SEPARATE SPEED SENSOR FRONT RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


39. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH

C107513
  1. Remove the clip and castle nut.

  1. C107514E01
    Using SST, separate the lower arm.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.


40. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


41. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C116895E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.


42. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


43. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


44. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


45. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.


46. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


47. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


48. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


49. SUSPEND ENGINE ASSEMBLY

D033567
  1. Install the 2 hangers in the correct direction.

  1. Attach the engine chain hoist to the hangers.

    CAUTION:
    Do not attempt to hang the engine by hooking the chain to any other part.

    Parts No.:
    Engine Hanger: 12281-21010

    Bolt:
    91642-81025

    Torque:
    40 N*m{ 408 kgf*cm , 29 ft.*lbf }


50. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

  1. C107979
    Remove the bolt and separate the engine moving control rod.

  1. Support the front suspension crossmember with a transmission jack.

  1. C107982
    Remove the 6 bolts and remove the suspension crossmember.


51. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET

C116856
  1. Remove the 4 bolts and the engine mounting control bracket.


52. SUPPORT MANUAL TRANSAXLE ASSEMBLY

53. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

C127626
  1. Remove the bolt and nut, then separate the engine mounting insulator LH.

  1. Remove the 5 bolts and the engine mounting insulator LH.


54. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

C127614
  1. Remove the 4 bolts and the engine mounting bracket LH.


55. REMOVE MANUAL TRANSAXLE ASSEMBLY

C063143
  1. Remove the 7 bolts and the manual transaxle.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →