B1610/13 Front Airbag Sensor RH Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2005
DESCRIPTION
The front airbag sensor RH consists of parts including the diagnostic circuit and the frontal deceleration sensor.When the center airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1610/13 is set when a malfunction is detected in the front airbag sensor RH circuit.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| B1610/13 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.
- Turn the ignition switch off.
- Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
- Disconnect the connector from the center airbag sensor assembly.
- Disconnect the connector from the steering pad.
- Disconnect the connector from the front seat outer belt assembly LH.
- Disconnect the connector from the front seat outer belt assembly RH.
- HINT:
- Skip the following steps if side airbags, curtain shield airbags, front passenger airbag and a knee airbag are not fitted.
- Disconnect the connector from the front passenger airbag assembly.
- Disconnect the connector from the front seat side airbag assembly LH.
- Disconnect the connector from the front seat side airbag assembly RH.
- Disconnect the connector from the curtain shield airbag assembly LH.
- Disconnect the connector from the curtain shield airbag assembly RH.
- Disconnect the connector from the driver side knee airbag assembly.
| 1. CHECK DTC OUTPUT |
![]() ![]() |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1610/13 is not output.
- HINT:
- DTCs other than DTC B1610/13 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR OPEN) |
![]() ![]() |
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH.
Using a service wire, connect A6-1 and A6-2 of connector E.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
D16-29 (+SR) - D16-27 (-SR)
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR SHORT) |
![]() ![]() |
Disconnect the service wire from connector E.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
D16-29 (+SR) - D16-27 (-SR)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+) |
![]() ![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester connection
Condition
Specified condition
D16-29 (+SR) - Body ground
Ignition switch on (IG)
Below 1 V
D16-27 (-SR) - Body ground
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | |
| 6. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
D16-29 (+SR) - Body ground
Always
1 MΩ or higher
D16-27 (-SR) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 7. CHECK FRONT AIRBAG SENSOR RH |
![]() ![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the front airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- Result:
Result
Proceed to
DTC B1610/13 is output.
A
DTC B1615/14 is output.
B
DTC B1610/13 and B1615/14 are not output.
C
- HINT:
- DTCs other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| C | ||
| ||
| 8. CHECK ENGINE ROOM MAIN WIRE (FOR OPEN) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
- HINT:
- The service wire has already been inserted into connector E.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
AD1-1 (+SR) - AD1-2 (-SR)
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 9. CHECK ENGINE ROOM MAIN WIRE (FOR SHORT) |
![]() ![]() |
Disconnect the service wire from connector E.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
AD1-1 (+SR) - AD1-2 (-SR)
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 10. CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester connection
Condition
Specified condition
AD1-1 (+SR) - Body ground
Ignition switch on (IG)
Below 1 V
AD1-2 (-SR) - Body ground
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | ||
| ||
| 11. CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
AD1-1 (+SR) - Body ground
Always
1 MΩ or higher
AD1-2 (-SR) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||






