2005-2008 Yaris · Service Manual BRAKE

ADJUSTMENT

Removal / installation · Vehicles built from Aug 2005


1. REMOVE REAR WHEEL (for Rear Drum Brake)

2. ADJUST REAR DRUM BRAKE SHOE CLEARANCE (for Rear Drum Brake)

F040023E03
  1. Provisionally install the 2 hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 12 notches.

  1. Install the hole plug.


3. INSTALL REAR WHEEL (for Rear Drum Brake)

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


4. INSPECT PARKING BRAKE LEVER TRAVEL
  1. Slowly pull the parking brake lever to the fully applied position, counting the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    Rear Brake Type
    Number of clicks
    Drum
    6 to 9
    Disc
    4 to 7


5. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

6. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)

C109005E01
  1. Disengage the 6 claws and remove the shifting hole cover.


7. REMOVE CONSOLE BOX REAR COVER

C109006E01
  1. Disengage the 8 claws and remove the console box rear cover.


8. REMOVE CONSOLE BOX CARPET

C109008
  1. Remove the console box carpet.


9. REMOVE REAR CONSOLE BOX ASSEMBLY

C116873
  1. Remove the bolt and disengage the 2 clips to remove the console box.


10. ADJUST PARKING BRAKE LEVER TRAVEL (for Rear Drum Brake)

C116905E01
  1. Loosen the lock nut and turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.

    Parking brake lever travel:
    6 to 9 clicks at 200 N (20 kgf 45 lbf)

  1. Tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the brake warning light illuminates.

    Standard:
    Brake warning light always illuminates at the first click.


11. ADJUST PARKING BRAKE LEVER TRAVEL (for Rear Disc Brake)
  1. Completely release the parking brake lever.

  1. Loosen the lock nut and adjusting nut to completely release the parking brake cable.

  1. Strongly step on the brake pedal 3 to 5 times with the engine stopped.

  1. C116905E01
    Turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.

    Parking brake lever travel:
    4 to 7 clicks at 200 N (20 kgf 45 lbf)

  1. Tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check whether the parking brake drags or not.

  1. C108996E01
    Release the parking brake lever and check that the clearance measurement between the rear disc brake cylinder operation lever and the stopper is within the specified range.

    Clearance:
    0 to 0.5 mm (0 to 0.02 in.)

  1. When operating the parking brake lever, check that the brake warning light illuminates.

    Standard:
    Brake warning light always illuminates at the first click.


12. INSTALL REAR CONSOLE BOX ASSEMBLY

C116873
  1. Engage the 2 clips and install the console box with the bolt.


13. INSTALL CONSOLE BOX CARPET

C109008
  1. Install the console box carpet.


14. INSTALL CONSOLE BOX REAR COVER

C109006E01
  1. Engage the 8 claws to install the console box rear cover.


15. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)

C109005E01
  1. Engage the 6 claws to install the shifting hole cover.


16. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
← PROBLEM SYMPTOMS TABLE (from Aug 2005)PROBLEM SYMPTOMS TABLE (from Nov 2005) →